- 您現在的位置：買賣IC網 > PDF目錄369678 > CYCLONE08UM MON08 Cyclone Users Manual PDF資料下載
參數資料
| 型號： | CYCLONE08UM |
| 英文描述： | MON08 Cyclone Users Manual |
| 中文描述： | 的MON08氣旋用戶手冊 |
| 文件頁數： | 61/64頁 |
| 文件大小： | 756K |
| 代理商： | CYCLONE08UM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁當前第61頁第62頁第63頁第64頁
MON08 Cyclone User Manual
59
P&E
Microcomputer
Systems, Inc.
MON08 CYCLONE
analyzing the reset of the status bits.
1 – Device echoed some security bytes:
The monitor resident in a 68HC08 device automatically echoes every
incoming character when it is in monitor mode. A valid character
transmitted from the PC should be echoed once by the loopback circuitry
on the board and once by the monitor of the target processor itself. This
status indicates whether or not the second echoed character from the
monitor response was received when one of the security bytes was
transmitted. If the status is ‘N’, which indicates that the character was not
received, or not received properly, it is most likely due to one of the
following reasons:
1. The baud rate specified was incorrect.
2. The part did not start the monitor mode security check on reset.
Signals to force monitor mode may be incorrect.
3. No Power to the ICS.
If this status bit responded with an ‘N’, you must correct this before
analyzing the reset of the status bits.
2 – Device echoed all security bytes:
In order to pass security, the software must send 8 security bytes to the
processor. The processor should echo each of these eight bytes twice. If all
8 bytes did not get the proper two-byte echo, this flag will be ‘N’. Reasons
for this include:
1. The part did not start the monitor mode security check on reset.
Signals to force monitor mode may be incorrect.
2. The baud rate specified was incorrect.
3. The processor was not reset properly. Check the “Target Hardware
Type” and if you are connecting to a class II board, check the “MON08
cable communication connections type” in the “advanced settings”
dialog.
3 – Device signaled monitor mode with a break:
Once the processor has properly received the 8 bytes from the PC software
to complete its security check, it should transmit a break character to the
PC signaling entry into monitor mode. This break should be sent regardless
of whether the security check was successfully passed. If a break was not
received from the processor, this flag will be ‘N’. Reasons for this include:
1. The baud rate specified was incorrect.
2. The processor was not reset properly. Check the “Target Hardware
相關PDF資料 |
PDF描述 |
|---|---|
| CYK001M16SCCAU | Memory |
| CYK001M16ZCCAU | Memory |
| CYK512K16SCCAU | Memory |
| CYL2T0201-AIP | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| CYM1910PV-25C | SYNC SRAM|16KX68|CMOS|DIP|104PIN|PLASTIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CYCLONEIII VIDEO DEV KIT | 制造商:Altera Corporation 功能描述:CYCLONEIII VIDEO DEV KIT*NIC* |
| CYCLONEMAX | 功能描述:程序設計器 - 基于處理器 CYCLONE MAX FLASH PROGRA RoHS:否 制造商:Olimex Ltd. 產品:Programmers 工具用于評估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口類型:USB 工作電源電壓:1.8 V to 5.5 V |
| CYCLONEMAX | 制造商:Freescale Semiconductor 功能描述:Stand-alone in-circuit programmer/debugg |
| CYD01S18V | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:FLEx18⑩ 3.3V 64K/128K/256K/512K x 18 Synchronous Dual-Port RAM |
| CYD01S18V-133BBC | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:FLEx18⑩ 3.3V 64K/128K/256K/512K x 18 Synchronous Dual-Port RAM |
發布緊急采購，3分鐘左右您將得到回復。