參數資料
型號： CYCLONE08UM
英文描述： MON08 Cyclone Users Manual
中文描述： 的MON08氣旋用戶手冊
文件頁數： 60/64頁
文件大小： 756K
代理商： CYCLONE08UM
58
MON08 Cyclone User Manual
P&E
Microcomputer
Systems, Inc.
MON08 CYCLONE
This dialog can also be used by the user to manually enter the proper security
bytes via the USER setting, or to load the security bytes from the same .S19
file which was programmed. The bytes are loaded from an .S19 file by clicking
the “Load from S19” button.
IGNORE security failure and enter monitor mode
This checkbox can be used to cause the software to ignore a failure to
properly pass the 68HC08 security check. If the checkbox is set, the
software will attempt to establish monitor mode communications
regardless of the security status. As long as the Baud and Port are correct,
and the device has been properly powered, this will allow monitor mode
entry. Note that by ignoring the security check failure, you may use
monitor mode, but the ROM/Flash will not be accessible.
The checkbox can be set to bechecked on startup via the
FORCEBYPASS
command-line parameter, which will cause the software to ignore security
check failure. This checkbox can be overridden to be
un
checked on startup
via the
FORCEPASS
command-line parameter, which will cause the
software to pop-up the connection dialog when the security check has
failed. Note that if a connection is not established for a reason other than
security failure, the connection dialog will always appear.
6.3.3
STATUS
The status area consists of one status string following the “Status:” label, and
seven items which list the state of the last attempt to connect to a target and
pass security. The description for these items is as follows:
0 – ICS Hardware loopback detected:
Every ICS or board which supports MON08 has a serial loopback in
hardware which, by connecting the transmit and receive lines,
automatically echoes characters from the PC. A valid character transmitted
from the PC should be echoed once by the loopback circuitry on the board
and once by the monitor of the target processor itself. This status indicates
whether or not the first echoed character from the hardware loopback was
received when one of the security bytes was transmitted. If the status is
‘N’, which indicates that the character was not received, it is most likely
due to one of the following reasons:
1. Wrong Com Port specified.
2. The baud rate specified was incorrect (probably too low).
3. The ICS/Target is not connected.
4. No Power to the ICS.
If this status bit responded with an ‘N’, you must correct this before
相關PDF資料
PDF描述
CYK001M16SCCAU Memory
CYK001M16ZCCAU Memory
CYK512K16SCCAU Memory
CYL2T0201-AIP Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
CYM1910PV-25C SYNC SRAM|16KX68|CMOS|DIP|104PIN|PLASTIC
相關代理商/技術參數
參數描述
CYCLONEIII VIDEO DEV KIT 制造商:Altera Corporation 功能描述:CYCLONEIII VIDEO DEV KIT*NIC*
CYCLONEMAX 功能描述:程序設計器 - 基于處理器 CYCLONE MAX FLASH PROGRA RoHS:否 制造商:Olimex Ltd. 產品:Programmers 工具用于評估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口類型:USB 工作電源電壓:1.8 V to 5.5 V
CYCLONEMAX 制造商:Freescale Semiconductor 功能描述:Stand-alone in-circuit programmer/debugg
CYD01S18V 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:FLEx18⑩ 3.3V 64K/128K/256K/512K x 18 Synchronous Dual-Port RAM
CYD01S18V-133BBC 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:FLEx18⑩ 3.3V 64K/128K/256K/512K x 18 Synchronous Dual-Port RAM
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*