- 您現在的位置：買賣IC網 > PDF目錄369678 > CYCLONE08UM MON08 Cyclone Users Manual PDF資料下載
參數資料
| 型號： | CYCLONE08UM |
| 英文描述： | MON08 Cyclone Users Manual |
| 中文描述： | 的MON08氣旋用戶手冊 |
| 文件頁數： | 41/64頁 |
| 文件大小： | 756K |
| 代理商： | CYCLONE08UM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
MON08 Cyclone User Manual
39
P&E
Microcomputer
Systems, Inc.
MON08 CYCLONE
will perform a “Verify Module” on the target device. Every byte of the target
memory to be verified is read and compared with the contents within the
CYCLONE.
5.7
Image Description
The CYCLONE Configuration Utility allows the user to summarize the
purpose of current configuration for future reference. The description will be
either programmed into the CYCLONE or saved into a file (encrypted).
This field will not affect the CYCLONE operations with the target.
5.8
Save Image
“Save Image to Cyclone” allows the current configuration to be programmed
into the CYCLONE. The CYCLONE will then be ready for operations.
The “PC Serial Port” specifies which COM port the PC uses to communicate
with the CYCLONE to program the configurations.
“Save Image to File” allows the user to save the configuration into a file, which
may be used for future reference, e.g., comparing the CYCLONE contents
with the file to see if they are the same.
5.9
Stand-Alone Operation Procedure
The following steps must be followed in order for the CYCLONE to operate
properly:
1. Turn off the target power supply if the “POWER IN” Jack is adopted.
2. Turn off the MON08 CYCLONE board power.
3. Set the correct Jumper settings.
3.1
Choose the target voltage (Jumper 1 for 5V targets or Jumper 2
for 3.3V targets).
3.2
If applicable, set the Jumpers 3, 4, and 5 to obtain target power
from the MON08 CYCLONE.
4. Connect the target power supply to the “POWER IN” Jack, if applica-
ble.
5. Connect the “POWER OUT” Jack to the target board power, if applica-
ble.
6. Connect the MON08 Header Ribbon Cable to the target MON08 port.
7. Turn on the MON08 CYCLONE board power.
8. Turn on the target power supply, if applicable.
相關PDF資料 |
PDF描述 |
|---|---|
| CYK001M16SCCAU | Memory |
| CYK001M16ZCCAU | Memory |
| CYK512K16SCCAU | Memory |
| CYL2T0201-AIP | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| CYM1910PV-25C | SYNC SRAM|16KX68|CMOS|DIP|104PIN|PLASTIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CYCLONEIII VIDEO DEV KIT | 制造商:Altera Corporation 功能描述:CYCLONEIII VIDEO DEV KIT*NIC* |
| CYCLONEMAX | 功能描述:程序設計器 - 基于處理器 CYCLONE MAX FLASH PROGRA RoHS:否 制造商:Olimex Ltd. 產品:Programmers 工具用于評估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口類型:USB 工作電源電壓:1.8 V to 5.5 V |
| CYCLONEMAX | 制造商:Freescale Semiconductor 功能描述:Stand-alone in-circuit programmer/debugg |
| CYD01S18V | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:FLEx18⑩ 3.3V 64K/128K/256K/512K x 18 Synchronous Dual-Port RAM |
| CYD01S18V-133BBC | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:FLEx18⑩ 3.3V 64K/128K/256K/512K x 18 Synchronous Dual-Port RAM |
發布緊急采購，3分鐘左右您將得到回復。