- 您現在的位置：買賣IC網 > PDF目錄366974 > CY24233 Clocks and Buffers PDF資料下載
參數資料
| 型號： | CY24233 |
| 英文描述： | Clocks and Buffers |
| 中文描述： | 時鐘和緩沖器 |
| 文件頁數： | 3/15頁 |
| 文件大?。?/td> | 150K |
| 代理商： | CY24233 |
CY24239
Document #: 38-07038 Rev. **
Page 3 of 15
Functional Description
I/O Pin Operation
Pins 2, 8, 9, 29, and 30 are dual-purpose l/O pins. Upon power-
up these pins act as logic inputs, allowing the determination of
assigned device functions. A short time after power-up, the
logic state of each pin is latched and the pins become clock
outputs. This feature reduces device pin count by combining
clock outputs with input select pins.
An external 10-k
“
strapping
”
resistor is connected between
the l/O pin and ground or V
DD
. Connection to ground sets a
latch to
“
0,
”
connection to V
DD
sets a latch to
“
1.
”
Figure 1
and
Figure 2
show two suggested methods for strapping resistor
connections.
Upon CY24239 power-up, the first 2 ms of operation is used
for input logic selection. During this period, the five I/O pins (2,
8, 9, 29, 30) are three-stated, allowing the output strapping
resistor on the l/O pins to pull the pins and their associated
capacitive clock load to either a logic HIGH or LOW state. At
the end of the 2-ms period, the established logic
“
0
”
or
“
1
”
condition of the l/O pin is latched. Next the output buffer is
enabled, converting the l/O pins into operating clock outputs.
The 2-ms timer starts when V
DD
reaches 2.0V. The input bits
can only be reset by turning V
DD
off and then back on again.
It should be noted that the strapping resistors have no signifi-
cant effect on clock output signal integrity. The drive imped-
ance of clock output (<40
, nominal), which is minimally af-
fected by the 10-k
strap to ground or V
DD
. As with the series
termination resistor, the output strapping resistor should be
placed as close to the l/O pin as possible in order to keep the
interconnecting trace short. The trace from the resistor to
ground or V
DD
should be kept less than two inches in length to
prevent system noise coupling during input logic sampling.
When the clock outputs are enabled following the 2-ms input
period, the specified output frequency is delivered on the pin,
assuming that V
DD
has stabilized. If V
DD
has not yet reached
full value, output frequency initially may be below target but will
increase to target once V
DD
voltage has stabilized. In either
case, a short output clock cycle may be produced from the
CPU clock outputs when the outputs are enabled.
Power-on
Reset
Timer
Output Three-state
Data
Latch
Hold
Output
Low
Q
D
CY24239
V
DD
Clock Load
R
10 k
Output
Buffer
(Load Option 1)
10 k
(Load Option 0)
Output Strapping Resistor
Series Termination Resistor
Figure 1. Input Logic Selection Through Resistor Load Option
Power-on
Reset
Timer
Output Three-state
Data
Latch
Hold
Output
Low
Q
D
CY24239
V
DD
Clock Load
R
10 k
Output
Buffer
Output Strapping Resistor
Series Termination Resistor
Jumper Options
Figure 2. Input Logic Selection Through Jumper Option
Resistor Value R
相關PDF資料 |
PDF描述 |
|---|---|
| CY24712 | Clocks and Buffers |
| CY25000 | Clocks and Buffers |
| CY25245 | Clocks and Buffers |
| CY25562 | Clocks and Buffers |
| CY25562 | Spread Spectrum Clock Generator(擴頻時鐘發生器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CY24239 | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Spread Spectrum Frequency Timing Generator |
| CY24239PVC | 功能描述:鎖相環 - PLL MediaClock Clock RoHS:否 制造商:Silicon Labs 類型:PLL Clock Multiplier 電路數量:1 最大輸入頻率:710 MHz 最小輸入頻率:0.002 MHz 輸出頻率范圍:0.002 MHz to 808 MHz 電源電壓-最大:3.63 V 電源電壓-最小:1.71 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:QFN-36 封裝:Tray |
| CY24239PVCT | 制造商:Cypress Semiconductor 功能描述: |
| CY24240ASC | 功能描述:時鐘緩沖器 MediaClock Clock COM RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲（最大值）: 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel |
| CY24240SC | 制造商:Cypress Semiconductor 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。