- 您現在的位置：買賣IC網 > PDF目錄26505 > CP2110-F01-GM (SILICON LABORATORIES) PDF資料下載
參數資料
| 型號： | CP2110-F01-GM |
| 廠商： | SILICON LABORATORIES |
| 元件分類： | 總線控制器 |
| 中文描述： | UNIVERSAL SERIAL BUS CONTROLLER, QCC24 |
| 封裝： | 4 X 4 MM, LEAD FREE, MO-220WGGD, QFN-24 |
| 文件頁數： | 8/26頁 |
| 文件大?。?/td> | 244K |
| 代理商： | CP2110-F01-GM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
CP2110
16
Rev. 1.1
6. USB Function Controller and Transceiver
The Universal Serial Bus (USB) function controller in the CP2110 is a USB 2.0-compliant, full-speed device with
integrated transceiver and on-chip matching and pullup resistors. The USB function controller manages all data
transfers between the USB and the UARTs as well as command requests generated by the USB host controller
and commands for controlling the function of the UARTs and GPIO pins.
The USB Suspend and Resume modes are supported for power management of both the CP2110 device as well
as external circuitry. The CP2110 enters Suspend mode when Suspend signaling is detected on the bus. Upon
entering Suspend mode, the Suspend signals are asserted. The Suspend signals are also asserted after a CP2110
reset until device configuration during USB Enumeration is complete. SUSPEND is logic high when the device is in
the Suspend state, and logic low when the device is in normal mode. The SUSPEND pin has the opposite logic
value of the SUSPEND pin.
The CP2110 exits Suspend mode when any of the following occur: Resume signaling is detected or generated, a
USB Reset signal is detected, or a device reset occurs. SUSPEND and SUSPEND are weakly pulled to VIO in a
high impedance state during a CP2110 reset. If this behavior is undesirable, a strong pulldown (10 k
) can be used
to ensure SUSPEND remains low during reset.
The logic level and output mode (push-pull or open-drain) of various pins during USB Suspend is configurable in
the PROM. See Section 9 for more information.
相關PDF資料 |
PDF描述 |
|---|---|
| CPC1009NTR | |
| CPC1009N | |
| CPC1014NTR | |
| CPC1014N | |
| CPC1019N | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CP2110-F01-GMR | 功能描述:輸入/輸出控制器接口集成電路 HID USB-UART bridge RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| CP2110-F02-GM1 | 功能描述:輸入/輸出控制器接口集成電路 HID USB-UART bridge RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| CP2110-F02-GM1R | 功能描述:輸入/輸出控制器接口集成電路 HID USB-UART bridge RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| CP2110-GM | 制造商:Silicon Laboratories Inc 功能描述:USB TO UART BRIDGE 28QFN - Rail/Tube |
| CP2-11-10L | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
發布緊急采購，3分鐘左右您將得到回復。