- 您現在的位置：買賣IC網 > PDF目錄26505 > CP2110-F01-GM (SILICON LABORATORIES) PDF資料下載
參數資料
| 型號： | CP2110-F01-GM |
| 廠商： | SILICON LABORATORIES |
| 元件分類： | 總線控制器 |
| 中文描述： | UNIVERSAL SERIAL BUS CONTROLLER, QCC24 |
| 封裝： | 4 X 4 MM, LEAD FREE, MO-220WGGD, QFN-24 |
| 文件頁數： | 11/26頁 |
| 文件大?。?/td> | 244K |
| 代理商： | CP2110-F01-GM |
CP2110
Rev. 1.1
19
8.1. GPIO.0—Clock Output
GPIO.0 is configurable to output a configurable CMOS clock output. The clock output appears at the pin at the
same time the device completes enumeration and exits USB Suspend mode. The clock output is removed from the
pin when the device enters USB Suspend mode. The output frequency is configurable through the use of a divider
and the accuracy is specified in Table 6. When the divider is set to 0, the output frequency is 24 MHz. For divider
values between 1 and 255, the output frequency is determined by the formula:
Equation 4. GPIO.0 Clock Output Frequency
This divider is independent from the divider used to set UART baud rate.
8.2. GPIO.1-2—Hardware Flow Control (RTS and CTS)
By default, GPIO.1 and GPIO.2 are configured to operate as the hardware flow control pins RTS and CTS. In
addition to the GPIO PROM configuration, the device must be configured to use hardware flow control to use these
pins.
RTS, or Ready To Send, is an active-low output from the CP2110 and indicates to the external UART device that
the CP2110’s UART RX FIFO has not reached the watermark level of 450 bytes and is ready to accept more data.
When the amount of data in the RX FIFO reaches the watermark, the CP2110 pulls RTS high to indicate to the
external UART device to stop sending data.
CTS, or Clear To Send, is an active-low input to the CP2110 and is used by the external UART device to indicate to
the CP2110 when the external UART device’s RX FIFO is getting full. The CP2110 will not send more than two
bytes of data once CTS is pulled high.
Figure 8. Hardware Flow Control Typical Connection Diagram
GPIO.0 Clock Frequency
24 MHz
2Divider
------------------------------
=
CP2110
RS232
System
TX
RX
TX
RX
RTS
CTS
GPIO.1 – RTS
GPIO.2 – CTS
相關PDF資料 |
PDF描述 |
|---|---|
| CPC1009NTR | |
| CPC1009N | |
| CPC1014NTR | |
| CPC1014N | |
| CPC1019N | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CP2110-F01-GMR | 功能描述:輸入/輸出控制器接口集成電路 HID USB-UART bridge RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| CP2110-F02-GM1 | 功能描述:輸入/輸出控制器接口集成電路 HID USB-UART bridge RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| CP2110-F02-GM1R | 功能描述:輸入/輸出控制器接口集成電路 HID USB-UART bridge RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| CP2110-GM | 制造商:Silicon Laboratories Inc 功能描述:USB TO UART BRIDGE 28QFN - Rail/Tube |
| CP2-11-10L | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
發布緊急采購，3分鐘左右您將得到回復。