- 您現在的位置：買賣IC網 > PDF目錄379934 > COP8SDR9IMT7 (NATIONAL SEMICONDUCTOR CORP) 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout PDF資料下載
參數資料
| 型號： | COP8SDR9IMT7 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout |
| 中文描述： | 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDSO48 |
| 封裝： | TSSOP-48 |
| 文件頁數： | 56/80頁 |
| 文件大?。?/td> | 972K |
| 代理商： | COP8SDR9IMT7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁當前第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
15.0 Interrupts
(Continued)
15.4.2.1 Programming Example: External Interrupt
PSW
CNTRL
RBIT
RBIT
SBIT
SBIT
SBIT
WAIT:
JP
.
.
.
.=0FF
VIS
=00EF
=00EE
0,PORTGC
0,PORTGD
IEDG, CNTRL
GIE, PSW
EXEN, PSW
WAIT
; G0 pin configured Hi-Z
; Ext interrupt polarity; falling edge
; Set the GIE bit
; Enable the external interrupt
; Wait for external interrupt
; The interrupt causes a
; branch to address 0FF
; The VIS causes a branch to
; interrupt vector table
.
.
.
.=01FA
.ADDRW SERVICE
; Vector table (within 256 byte
; of VIS inst.) containing the ext
; interrupt service routine
.
.
.
SERVICE:
; Interrupt Service Routine
; Reset ext interrupt pend. bit
RBIT,EXPND,PSW
.
.
.
RET I
; Return, set the GIE bit
15.5 PORT L INTERRUPTS
Port L provides the user with an additional eight fully select-
able, edge sensitive interrupts which are all vectored into the
same service subroutine.
The interrupt from Port L shares logic with the wake-up
circuitry. The register WKEN allows interrupts from Port L to
be individually enabled or disabled. The register WKEDG
specifies the trigger condition to be either a positive or a
negative edge. Finally, the register WKPND latches in the
pending trigger conditions.
The GIE (Global Interrupt Enable) bit enables the interrupt
function.
A control flag, LPEN, functions as a global interrupt enable
for Port L interrupts. Setting the LPEN flag will enable inter-
rupts and vice versa. A separate global pending flag is not
needed since the register WKPND is adequate.
Since Port L is also used for waking the device out of the
HALT or IDLE modes, the user can elect to exit the HALT or
IDLE modes either with or without the interrupt enabled. If he
elects to disable the interrupt, then the device will restart
execution from the instruction immediately following the in-
struction that placed the microcontroller in the HALT or IDLE
modes. In the other case, the device will first execute the
interrupt service routine and then revert to normal operation.
(See HALT MODE for clock option wake-up information.)
15.6 INTERRUPT SUMMARY
The device uses the following types of interrupts, listed
below in order of priority:
1.
The Software Trap non-maskable interrupt, triggered by
the INTR (00 opcode) instruction. The Software Trap is
acknowledged immediately. This interrupt service rou-
tine can be interrupted only by another Software Trap.
The Software Trap should end with two RPND instruc-
tions followed by a re-start procedure.
Maskable interrupts, triggered by an on-chip peripheral
block or an external device connected to the device.
Under ordinary conditions, a maskable interrupt will not
interrupt any other interrupt routine in progress. A
maskable interrupt routine in progress can be inter-
rupted by the non-maskable interrupt request. A
maskable interrupt routine should end with an RETI
instruction or, prior to restoring context, should return to
execute the VIS instruction. This is particularly useful
when exiting long interrupt service routines if the time
between interrupts is short. In this case the RETI instruc-
tion would only be executed when the default VIS rou-
tine is reached.
While executing from the Boot ROM for ISP or virtual E2
operations, the hardware will disable interrupts from oc-
curring. The hardware will leave the GIE bit in its current
state, and if set, the hardware interrupts will occur when
execution is returned to Flash Memory. Subsequent in-
terrupts, during ISP operation, from the same interrupt
source will be lost.
2.
3.
C
www.national.com
56
相關PDF資料 |
PDF描述 |
|---|---|
| COP8SBR9IMT8 | 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout |
| COP8SCR9IMT8 | 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout |
| COP8SDR9IMTA8 | 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout |
| COP8SCR9HLQ7 | 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout |
| COP8SDR9HLQ7 | 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout |
相關代理商/技術參數 |
參數描述 |
|---|---|
| COP8SDR9IMT8 | 功能描述:IC MCU EEPROM 8BIT 32K 48-TSSOP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:COP8™ 8S 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C，IrDA，LIN，SPI，UART/USART 外圍設備:DMA，PDR，POR，PVD，PWM，溫度傳感器，WDT 輸入/輸出數:26 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN，36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND |
| COP8SDR9IMTA8 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout |
| COP8SDR9KMT8 | 功能描述:IC MCU EEPROM 8BIT 32K 56-TSSOP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:COP8™ 8S 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| COP8SDR9KMTA8 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout |
| COP8SDR9LVA7 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout |
發布緊急采購，3分鐘左右您將得到回復。