- 您現在的位置：買賣IC網 > PDF目錄379934 > COP8SDR9IMT7 (NATIONAL SEMICONDUCTOR CORP) 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout PDF資料下載
參數資料
| 型號： | COP8SDR9IMT7 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout |
| 中文描述： | 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDSO48 |
| 封裝： | TSSOP-48 |
| 文件頁數： | 54/80頁 |
| 文件大?。?/td> | 972K |
| 代理商： | COP8SDR9IMT7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁當前第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
15.0 Interrupts
(Continued)
15.4 NON-MASKABLE INTERRUPT
15.4.1 Pending Flag
There is a pending flag bit associated with the non-maskable
Software Trap interrupt, called STPND. This pending flag is
not memory-mapped and cannot be accessed directly by the
software.
The pending flag is reset to zero when a device Reset
occurs. When the non-maskable interrupt occurs, the asso-
ciated pending bit is set to 1. The interrupt service routine
should contain an RPND instruction to reset the pending flag
to zero. The RPND instruction always resets the STPND
flag.
15.4.2 Software Trap
The Software Trap is a special kind of non-maskable inter-
rupt which occurs when the INTR instruction (used to ac-
knowledge interrupts) is fetched from program memory and
placed in the instruction register. This can happen in a
variety of ways, usually because of an error condition. Some
examples of causes are listed below.
If the program counter incorrectly points to a memory loca-
tion beyond the programmed Flash memory space, the un-
used memory location returns zeros which is interpreted as
the INTR instruction.
If the stack is popped beyond the allowed limit (address 06F
Hex), a 7FFF will be loaded into the PC. Since the Option
Register resides at this location, and to maintain the integrity
of the stack overpop protection, the Flash memory will return
a zero on an instruction fetch and a software trap will be
triggered.
A Software Trap can be triggered by a temporary hardware
condition such as a brownout or power supply glitch.
The Software Trap has the highest priority of all interrupts.
When a Software Trap occurs, the STPND bit is set. The GIE
bit is not affected and the pending bit (not accessible by the
user) is used to inhibit other interrupts and to direct the
program to the ST service routine with the VIS instruction.
Nothing can interrupt a Software Trap service routine except
for another Software Trap. The STPND can be reset only by
the RPND instruction or a chip Reset.
The Software Trap indicates an unusual or unknown error
condition. Generally, returning to normal execution at the
point where the Software Trap occurred cannot be done
reliably. Therefore, the Software Trap service routine should
re-initialize the stack pointer and perform a recovery proce-
dure that re-starts the software at some known point, similar
to a device Reset, but not necessarily performing all the
same functions as a device Reset. The routine must also
execute the RPND instruction to reset the STPND flag.
Otherwise, all other interrupts will be locked out. To the
extent possible, the interrupt routine should record or indi-
cate the context of the device so that the cause of the
Software Trap can be determined.
If the user wishes to return to normal execution from the
point at which the Software Trap was triggered, the user
must first execute RPND, followed by RETSK rather than
RETI or RET. This is because the return address stored on
the stack is the address of the INTR instruction that triggered
the interrupt. The program must skip that instruction in order
to proceed with the next one. Otherwise, an infinite loop of
Software Traps and returns will occur.
Programming a return to normal execution requires careful
consideration. If the Software Trap routine is interrupted by
another Software Trap, the RPND instruction in the service
routine for the second Software Trap will reset the STPND
flag; upon return to the first Software Trap routine, the
10138933
FIGURE 27. VIS Operation
C
www.national.com
54
相關PDF資料 |
PDF描述 |
|---|---|
| COP8SBR9IMT8 | 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout |
| COP8SCR9IMT8 | 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout |
| COP8SDR9IMTA8 | 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout |
| COP8SCR9HLQ7 | 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout |
| COP8SDR9HLQ7 | 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout |
相關代理商/技術參數 |
參數描述 |
|---|---|
| COP8SDR9IMT8 | 功能描述:IC MCU EEPROM 8BIT 32K 48-TSSOP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:COP8™ 8S 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C，IrDA，LIN，SPI，UART/USART 外圍設備:DMA，PDR，POR，PVD，PWM，溫度傳感器，WDT 輸入/輸出數:26 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN，36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND |
| COP8SDR9IMTA8 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout |
| COP8SDR9KMT8 | 功能描述:IC MCU EEPROM 8BIT 32K 56-TSSOP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:COP8™ 8S 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| COP8SDR9KMTA8 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout |
| COP8SDR9LVA7 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout |
發布緊急采購，3分鐘左右您將得到回復。