- 您現在的位置：買賣IC網 > PDF目錄385241 > CN8332EXF PCM Transceiver PDF資料下載
參數資料
| 型號： | CN8332EXF |
| 英文描述： | PCM Transceiver |
| 中文描述： | 收發器的PCM |
| 文件頁數： | 31/48頁 |
| 文件大?。?/td> | 434K |
| 代理商： | CN8332EXF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
CN8331/CN8332/CN8333
2.0 Functional Description
Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit
2.4 Additional CN8331/CN8332/CN8333 Functions
100604B
Conexant
2-13
2.4 Additional CN8331/CN8332/CN8333
Functions
2.4.1 Bias Generator
To achieve good isolation between the channels, each channel utilizes an
independent power and ground to both transmit and receive. Additionally, each
channel has its own band gap voltage reference. Because only one external
resistor for current generation exists, only one band gap voltage can be used. The
band gap from Ch1 has been chosen for this task.
The 12.1 k
external resistor from pin RBIAS to ground, is specified to have
a tolerance of ±1%. This helps to keep tighter control on power dissipation and
circuit performance.
NOTE:
Capacitance should be kept to a minimum on the RBIAS pin.
2.4.2 Power-On Reset (POR)
A POR function is provided in the CN833x device to ensure all of the resettable
digital logic and analog control lines are starting from a known state. This circuit
uses a fixed RC timer (~1
μ
s); additionally, 128 clocks from REFCLK are counted
(after the RC timer has timed-out) before reset is deasserted, which begins timing
after a minimum supply voltage is reached (see
Table 2-2
).
2.4.3 Loopback Multiplexers (MUXes)
Two loopback MUXes per channel in the CN833x allow for local loopback
(terminal or framer side), remote loopback (cable side), or both (the AIS signal
follows the same path as the transmit data during loopback). The RLOS signal
monitors the RX cable inputs irrespective of any loopback.
In remote loopback, set by asserting pin RLOOP high, the receive data
(retimed after clock recovery but not decoded) loops back into the pulse shaper in
place of the transmit data. Additionally, this data sent out the RPOS, RNEG, and
RCLK pins.
In local loopback, set by asserting pin LLOOP, the transmit data loops back
immediately from the encoder output to the decoder input in place of the received
data. Additionally, this data is sent out the TLINEP and TLINEM pins.
Powered by ICminer.com Electronic-Library Service CopyRight 2003
相關PDF資料 |
PDF描述 |
|---|---|
| CN8333EXF | PCM Transceiver |
| CN8394KTF | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| CN8398KBG | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| CN8398KPF | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| CN8471AKPF | Industrial Control IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CN8333EXF | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCM Transceiver |
| CN8333EXF28333-15ES1 | 制造商:Conexant 功能描述: |
| CN8366-000 | 制造商:TE Connectivity 功能描述:44/0412-22-9CS1038 |
| CN8371-000 | 制造商:TE Connectivity 功能描述:RNF-100-3/8-WH-SP-CS5004 制造商:TE Connectivity 功能描述:RNF-100-3/8-WH-SP-CS5004 - Bulk |
| CN8373-000 | 制造商:TE Connectivity 功能描述:XFFR-30-04/97 - Bulk |
發布緊急采購，3分鐘左右您將得到回復。