參數資料
型號： CLC031VEC
廠商： NATIONAL SEMICONDUCTOR CORP
元件分類： 消費家電
英文描述： SMPTE 292M/259M Digital Video Deserializer / Descrambler with Video and Ancilliary Data FIFOs
中文描述： SPECIALTY CONSUMER CIRCUIT, PQFP64
封裝： TQFP-64
文件頁數： 11/31頁
文件大?。?/td> 383K
代理商： CLC031VEC
Device Operation
(Continued)
The
SMPTE descrambler
receives NRZI serial data, con-
verts it to NRZ, then decodes it to either 10-bit standard
definition or 20-bit high definition parallel video data using
the reverse polynomial X
9
+ X
4
+ 1 as specified in the
respective standard: SMPTE 259M, SMPTE 344M (pro-
posed) or SMPTE 292M. The data reception bit order is
LSB-first. All data processing is done at the parallel rate.
The CLC031 incorporates circuitry that implements a
method for handling data that has been subjected to
LSB
dithering
. When so enabled, data from the de-scrambler is
routed for de-dithering. The
De-Dither Enable
bit in the
VIDEO INFO 0
control register enables this function. De-
dithering of data present in the vertical blanking interval can
be selectively enabled by use of the
V De-Dither Enable
bit
in the
VIDEO INFO 0
control register. The initial condition of
De-Dither Enable
and
V De-Dither Enable
is OFF.
The descrambler supplies signals to the
TRS character de-
tector
which identifies the presence of the valid video data.
The
TRS character detector
processes the timing refer-
ence signals which control raster framing. TRS (sync) char-
acters are detected and the video is aligned on word bound-
aries. Data is re-synchronized with the parallel word-rate
clock. Interraction and operation of the character alignment
control signals and indicators
Framing Mode
,
Framing En-
able
and
NSP
(New Sync Position) is described later in this
datasheet.
The CLC031 implements TRS character LSB-clipping as
prescribed in ITU-R BT.601. LSB-clipping causes all TRS
characters with a value between 000h and 003h to be forced
to 000h and all TRS characters with a value between 3FCh
and 3FFh to be forced to 3FFh. Clipping is done after de-
scrambling and de-dithering.
Once the PLL attains lock, the
video format detector
pro-
cesses the received data to determine the raster character-
istics (video data format) and configure the CLC031 to
handle it. This assures that the parallel output data will be
properly formatted, that the correct data rate is selected and
that ancilliary data and CRC/EDH data are correctly de-
tected and checked. Supported parallel data formats or sub-
formats may belong to any one of several component stan-
dards: SMPTE 125M, SMPTE 267M, SMPTE 260M, 274M,
295M or 296M. Refer to
Table 4
for the supported formats.
(See also the
Application Information
section for handling of
other raster formats or format extensions developed after
this device was designed). The detected video standard
information is passed to the device control system and
saved in the control registers from whence it may be read by
the user.
The CLC031 may be configured to operate in a single video
format by loading the appropriate
FORMAT SET[4:0]
control
data into the
FORMAT 0
control register. Also, the CLC031
may be configured to handle only the standard-definition
data formats by setting the
SD ONLY
bit or only the high-
definition data formats by setting the
HD ONLY
bit in the
FORMAT 0
control register. When both bits are reset, the
default condition, the part automatically detects the data rate
and range.
Aligned and de-processed parallel data passes into a
variable-depth
video FIFO
prior to output. Video FIFO depth
from 0 to 4 registers is set by a 3-bit word written into the
VIDEO FIFO Depth[2:0]
bits in the
ANC 0
control register.
The video FIFO permits adjustment of the parallel video data
output timing or delay at a parallel word rate. The occurence
of corresponding TRS indicator bits, EAV, SAV and NSP, in
the control register corresponds to the input register position
of the FIFO. This positioning permits a look-ahead function
in which the alignment status of the video data can be
determined up to four parallel clock periods prior to the
appearance of that data at the parallel data output.
The parallel video data is output on
DV[19:0]
. The 20-bit
parallel video data is organized so that for HDTV data, the
upper-order 10 bits
DV[19:10]
are luminance (luma) infor-
mation and the lower 10 bits
DV[9:0]
are colour difference
(chroma) information. SDTV data use the lower-order 10-bits
DV[9:0]
for both luma and chroma information. (The SDTV
parallel data is also duplicated on
DV[19:10]
).
V
is the
parallel output word rate clock signal. The frequency of
V
is appropriate to either the HD or SD data being processed.
Data is valid between the falling edges of a
V
cycle. Data
may be clocked into external devices on the rising-edge of
V
. The
DV[19:0]
and
V
CLK
signals are LVCMOS-
compatible.
20020106
FIGURE 1. Optional Input Biasing Scheme
C
www.national.com
11
相關PDF資料
PDF描述
CLC034 SMPTE 292M / 259M Adaptive Cable Equalizer
CLC034MA SMPTE 292M / 259M Adaptive Cable Equalizer
CLC103 Fast Settling, High Current Wideband Op Amp
CLC103AM Fast Settling, High Current Wideband Op Amp
CLC103AI Fast Settling, High Current Wideband Op Amp
相關代理商/技術參數
參數描述
CLC03-22N_-RC 制造商:ALLIED 制造商全稱:Allied Components International 功能描述:Ceramic Core Laser Cut Chip Inductor
CLC03-27N_-RC 制造商:ALLIED 制造商全稱:Allied Components International 功能描述:Ceramic Core Laser Cut Chip Inductor
CLC03-2N2_-RC 制造商:ALLIED 制造商全稱:Allied Components International 功能描述:Ceramic Core Laser Cut Chip Inductor
CLC03-2N7_-RC 制造商:ALLIED 制造商全稱:Allied Components International 功能描述:Ceramic Core Laser Cut Chip Inductor
CLC03-33N_-RC 制造商:ALLIED 制造商全稱:Allied Components International 功能描述:Ceramic Core Laser Cut Chip Inductor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*