- 您現在的位置：買賣IC網 > PDF目錄16425 > CDB42L51 (Cirrus Logic Inc)BOARD EVAL FOR CS42L51 CODEC PDF資料下載
參數資料
| 型號： | CDB42L51 |
| 廠商： | Cirrus Logic Inc |
| 文件頁數： | 38/43頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR CS42L51 CODEC |
| 標準包裝： | 1 |
| 主要目的： | 音頻編解碼器 |
| 嵌入式： | 是，其它 |
| 已用 IC / 零件： | CS42L51，CS8406，CS8415 |
| 主要屬性： | 立體聲數字音頻發射器和接收器 |
| 次要屬性： | 圖形用戶界面，S/PDIF 接口 |
| 已供物品： | 板，CD |
| 相關產品： | CS42L51-DNZR-ND - IC CODEC STEREO W/HDPN AMP 32QFN 598-1627-ND - IC CODEC STEREO W/HDPN AMP 32QFN CS42L51-CNZR-ND - IC CODEC LOW-V 24BIT 32-QFP 598-1045-ND - IC CODEC STEREO W/HDPN AMP 32QFN |
| 其它名稱： | 598-1005 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁
DS679F1
43
CS42L51
4.10
Software Mode
The control port is used to access the registers allowing the CODEC to be configured for the desired oper-
ational modes and formats. The operation of the control port may be completely asynchronous with respect
to the audio sample rates. However, to avoid potential interference problems, the control port pins should
remain static if no operation is required.
The control port operates in two modes: SPI and IC, with the CODEC acting as a slave device. Software
Mode is selected if there is a high-to-low transition on the AD0/CS pin after the RESET pin has been brought
high. IC Mode is selected by connecting the AD0/CS pin through a resistor to VL or DGND, thereby per-
manently selecting the desired AD0 bit address state.
4.10.1
SPI Control
In Software Mode, CS is the CS42L51 chip-select signal, CCLK is the control port bit clock (input into the
CS42L51 from the microcontroller), CDIN is the input data line from the microcontroller. Data is clocked
in on the rising edge of CCLK. The CODEC will only support write operations. Read request will be ig-
nored.
Figure 23 shows the operation of the control port in Software Mode. To write to a register, bring CS low.
The first seven bits on CDIN form the chip address and must be 1001010. The eighth bit is a read/write
indicator (R/W), which should be low to write. The next eight bits form the Memory Address Pointer (MAP),
which is set to the address of the register that is to be updated. The next eight bits are the data which will
be placed into the register designated by the MAP.
There is MAP auto-increment capability, enabled by the INCR bit in the MAP register. If INCR is a zero,
the MAP will stay constant for successive read or writes. If INCR is set to a 1, the MAP will auto-increment
after each byte is read or written, allowing block reads or writes of successive registers.
4.10.2
IC Control
In IC Mode, SDA is a bidirectional data line. Data is clocked into and out of the part by the clock, SCL.
There is no CS pin. Pin AD0 forms the least significant bit of the chip address and should be connected
through a resistor to VL or DGND as desired. The state of the pin is sensed while the CS42L51 is being
reset.
The signal timings for a read and write cycle are shown in Figure 24 and Figure 25. A Start condition is
defined as a falling transition of SDA while the clock is high. A Stop condition is a rising transition while
the clock is high. All other transitions of SDA occur while the clock is low. The first byte sent to the CS42L51
after a Start condition consists of a 7-bit chip address field and a R/W bit (high for a read, low for a write).
The upper 6 bits of the 7-bit address field are fixed at 100101. To communicate with a CS42L51, the chip
address field, which is the first byte sent to the CS42L51, should match 100101 followed by the setting of
the AD0 pin. The eighth bit of the address is the R/W bit. If the operation is a write, the next byte is the
Memory Address Pointer (MAP) which selects the register to be read or written. If the operation is a read,
4
5
6
7
CCLK
CHIP ADDRESS (WRITE)
MAP BYTE
DATA
1
0
1
0
1
0
CDIN
INCR
6
5
4
3
2
1
0
7
6
1
0
1
2
3
8
9
12
16 17
10 11
13 14 15
DATA +n
CS
7
6
1
0
Figure 23. Control Port Timing in SPI Mode
相關PDF資料 |
PDF描述 |
|---|---|
| GMM11DRKI | CONN EDGECARD 22POS DIP .156 SLD |
| UPJ1J151MHD6TO | CAP ALUM 150UF 63V 20% RADIAL |
| ECA22DTKI | CONN EDGECARD 44POS DIP .125 SLD |
| M1TXK-3436J | IDC CABLE - MSD34K/MC34G/X |
| GEM28DREI | CONN EDGECARD 56POS .156 EYELET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CDB42L51/FAE | 制造商:Cirrus Logic 功能描述:EVAL BOARD FOR THE CS42L51 PORTABLE STEREO CODEC - Bulk |
| CDB42L52 | 功能描述:音頻 IC 開發工具 Eval Bd LP CODEC w/classD Spkr Driver RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| CDB42L52/FAE | 制造商:Cirrus Logic 功能描述:EVAL BD LOW-VOLTAGE STEREO CODEC - Bulk |
| CDB42L55 | 功能描述:音頻 IC 開發工具 Eval Bd Ultra Low PWR Stereo Codec RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| CDB42L56 | 功能描述:音頻 IC 開發工具 Eval Bd 24Bit Ultra LP Ster CD w/clH HP RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
發布緊急采購，3分鐘左右您將得到回復。