- 您現在的位置：買賣IC網 > PDF目錄385185 > bq2011 (Benchmark Technology Group) Gas Gauge IC for High Discharge Rates(用于高放電率的氣體Gauge芯片) PDF資料下載
參數資料
| 型號： | bq2011 |
| 廠商： | Benchmark Technology Group |
| 英文描述： | Gas Gauge IC for High Discharge Rates(用于高放電率的氣體Gauge芯片) |
| 中文描述： | 氣體計IC，高放電率（用于高放電率的氣體計芯片） |
| 文件頁數： | 9/20頁 |
| 文件大小： | 181K |
| 代理商： | BQ2011 |
Communicating with the bq2011
The bq2011 includes a simple single-pin (DQ plus re-
turn) serial data interface. A host processor uses the in-
terface to access various bq2011 registers. Battery char-
acteristics may be easily monitored by adding a single
contact to the battery pack. The open-drain DQ pin on
the bq2011 should be pulled up by the host system, or may
be left floating if the serial interface is not used.
The interface uses a command-based protocol, where the
host processor sends a command byte to the bq2011.
The command directs the bq2011 to either store the next
eight bits of data received to a register specified by the
command byte or output the eight bits of data specified
by the command byte.
The communication protocol is asynchronous return-to-
one. Command and data bytes consist of a stream of eight
bits that have a maximum transmission rate of 333
bits/sec. The least-significant bit of a command or data
byte is transmitted first. The protocol is simple enough
that it can be implemented by most host processors using
either polled or interrupt processing. Data input from the
bq2011 may be sampled using the pulse-width capture
timers available on some microcontrollers.
Communication is normally initiated by the host proces-
sor sending a BREAK command to the bq2011.
BREAK is detected when the DQ pin is driven to a
logic-low state for a time, t
B
or greater.
should then be returned to its normal ready-high logic
state for a time, t
BR
. The bq2011 is now ready to receive
a command from the host processor.
A
The DQ pin
The return-to-one data bit frame consists of three distinct
sections. The first section is used to start the transmission
by either the host or the bq2011 taking the DQ pin to a
logic-low state for a period, t
STRH,B
. The next section is the
actual data transmission, where the data should be valid by
a period, t
DSU
, after the negative edge used to start commu-
nication. The data should be held for a period, t
DV
, to allow
thehostorbq2011tosamplethedatabit.
The final section is used to stop the transmission by return-
ing the DQ pin to a logic-high state by at least a period,
t
SSU
, after the negative edge used to start communication.
The final logic-high state should be held until a period, t
SV
,
to allow time to ensure that the bit transmission was
stopped properly. The timings for data and break commu-
nication are given in the serial communication timing
specificationandillustrationsections.
Communication with the bq2011 is always performed
with the least-significant bit being transmitted first.
Figure 3 shows an example of a communication se-
quence to read the bq2011 NAC register.
bq2011 Registers
The bq2011 command and status registers are listed in
Table 4 and described below.
Command Register (CMDR)
The write-only CMDR register is accessed when eight
valid command bits have been received by the bq2011.
The CMDR register contains two fields:
W/R bit
Command address
The W/R bit of the command register is used to select
whether the received command is for a read or a write
function.
9
bq2011
TD201101.eps
DQ
Break
0 0 0 0 0 0
1 0 1 0 0 1
Written by Host to bq2011
CMDR = 03h
Received by Host to bq2011
NAC = 65h
LSB
MSB
LSB
MSB
1
1
1 0
Figure 3. Typical Communication with the bq2011
相關PDF資料 |
PDF描述 |
|---|---|
| bq2012 | Gas Gauge IC With Slow-Charge Control(Gas Gauge芯片（帶慢充電控制）) |
| bq2013H | Gas Gauge IC for Power-Assist Applications(應用于電源援助的氣體Gauge芯片) |
| bq2014H | Low-Cost NiCd/NiMH Gas Gauge IC(低價格NiCd/NiMHGas Gauge芯片) |
| bq2014 | Gas Gauge IC with External Charge Control(氣體Gauge（帶外部電荷控制）) |
| bq2040 | Gas Gauge IC With SMBus Interface(氣體Gauge芯片（帶SMBus 接口）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BQ2011_05 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Gas Gauge IC for High Discharge Rates |
| BQ2011JPN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Battery Management |
| BQ2011JPN-N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Battery Management |
| BQ2011JSN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Battery Management |
| BQ2011K | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Gas Gauge IC for High Discharge Rates |
發布緊急采購，3分鐘左右您將得到回復。