參數資料
型號： AT89C51ID2-SLSUM
廠商： Atmel
文件頁數： 156/157頁
文件大?。?/td> 0K
描述： IC 8051 MCU FLASH 64K 44PLCC
產品培訓模塊： MCU Product Line Introduction
標準包裝： 972
系列： 89C
核心處理器： 8051
芯體尺寸： 8-位
速度： 60MHz
連通性： I²C，SPI，UART/USART
外圍設備： POR，PWM，WDT
輸入/輸出數： 34
程序存儲器容量： 64KB（64K x 8）
程序存儲器類型： 閃存
EEPROM 大?。?/td> 2K x 8
RAM 容量： 2K x 8
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 5.5 V
振蕩器型： 外部
工作溫度： -40°C ~ 85°C
封裝/外殼： 44-LCC（J 形引線）
包裝： 管件
配用： AT89OCD-01-ND - USB EMULATOR FOR AT8XC51 MCU
98
AT89C51ID2
4289C–8051–11/05
Serial Port Interface
(SPI)
The Serial Peripheral Interface Module (SPI) allows full-duplex, synchronous, serial
communication between the MCU and peripheral devices, including other MCUs.
Features
Features of the SPI Module include the following:
Full-duplex, three-wire synchronous transfers
Master or Slave operation
Eight programmable Master clock rates
Serial clock with programmable polarity and phase
Master Mode fault error flag with MCU interrupt capability
Write collision flag protection
Signal Description
Figure 36 shows a typical SPI bus configuration using one Master controller and many
Slave peripherals. The bus is made of three wires connecting all the devices.
Figure 36. SPI Master/Slaves Interconnection
The Master device selects the individual Slave devices by using four pins of a parallel
port to control the four SS pins of the Slave devices.
Master Output Slave Input
(MOSI)
This 1-bit signal is directly connected between the Master Device and a Slave Device.
The MOSI line is used to transfer data in series from the Master to the Slave. Therefore,
it is an output signal from the Master, and an input signal to a Slave. A Byte (8-bit word)
is transmitted most significant bit (MSB) first, least significant bit (LSB) last.
Master Input Slave Output
(MISO)
This 1-bit signal is directly connected between the Slave Device and a Master Device.
The MISO line is used to transfer data in series from the Slave to the Master. Therefore,
it is an output signal from the Slave, and an input signal to the Master. A Byte (8-bit
word) is transmitted most significant bit (MSB) first, least significant bit (LSB) last.
SPI Serial Clock (SCK)
This signal is used to synchronize the data movement both in and out of the devices
through their MOSI and MISO lines. It is driven by the Master for eight clock cycles
which allows to exchange one Byte on the serial lines.
Slave Select (SS)
Each Slave peripheral is selected by one Slave Select pin (SS). This signal must stay
low for any message for a Slave. It is obvious that only one Master (SS high level) can
Slave 1
MI
SO
MO
SI
SC
K
SS
MISO
MOSI
SCK
SS
POR
T
0
1
2
3
Slave 3
MI
SO
MO
SI
SCK
SS
Slave 4
MI
SO
MO
SI
SC
K
SS
Slave 2
MI
S
O
MO
S
I
SC
K
SS
VDD
Master
相關PDF資料
PDF描述
AT91SAM7X128B-CU IC MCU 128KB FLASH 100TFBGA
AT91SAM7XC128B-AU MCU ARM 128K HS FLASH 100-LQFP
ATSAM3U1CA-CU IC MCU 32BIT 64KB FLASH 100TFBGA
1981584-1 CONN RCPT MICRO USB TYPE AB
1981568-1 CONN RCPT MICRO USB B R/A SMD
相關代理商/技術參數
參數描述
AT89C51ID2-SMSIM 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Flash Microcontroller
AT89C51ID2-UM 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Flash Microcontroller
AT89C51RB2 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 16K/ 32K Bytes Flash
AT89C51RB2/RC2 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:AT89C51RB2/RC2 [Updated 4/03. 125 Pages]
AT89C51RB2_06 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 16K/ 32K Bytes Flash
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*