參數資料
型號: AT89C51ID2-SLSUM
廠商: Atmel
文件頁數: 129/157頁
文件大?。?/td> 0K
描述: IC 8051 MCU FLASH 64K 44PLCC
產品培訓模塊: MCU Product Line Introduction
標準包裝: 972
系列: 89C
核心處理器: 8051
芯體尺寸: 8-位
速度: 60MHz
連通性: I²C,SPI,UART/USART
外圍設備: POR,PWM,WDT
輸入/輸出數: 34
程序存儲器容量: 64KB(64K x 8)
程序存儲器類型: 閃存
EEPROM 大小: 2K x 8
RAM 容量: 2K x 8
電壓 - 電源 (Vcc/Vdd): 2.7 V ~ 5.5 V
振蕩器型: 外部
工作溫度: -40°C ~ 85°C
封裝/外殼: 44-LCC(J 形引線)
包裝: 管件
配用: AT89OCD-01-ND - USB EMULATOR FOR AT8XC51 MCU
73
AT89C51ID2
4289C–8051–11/05
and RAM contents are preserved. The status of the Port pins during Power-Down mode
is detailed in Table 57.
Note:
VCC may be reduced to as low as V
RET during Power-Down mode to further reduce
power dissipation. Take care, however, that VDD is not reduced until Power-Down mode
is invoked.
Entering Power-Down Mode
To enter Power-Down mode, set PD bit in PCON register. The AT89C51ID2 enters the
Power-Down mode upon execution of the instruction that sets PD bit. The instruction
that sets PD bit is the last instruction executed.
Exiting Power-Down Mode
Note:
If VCC was reduced during the Power-Down mode, do not exit Power-Down mode until
VCC is restored to the normal operating level.
There are two ways to exit the Power-Down mode:
1.
Generate an enabled external interrupt.
The AT89C51ID2 provides capability to exit from Power-Down using INT0#,
INT1#.
Hardware clears PD bit in PCON register which starts the oscillator and
restores the clocks to the CPU and peripherals. Using INTx# input,
execution resumes when the input is released (see Figure 26). Execution
resumes with the interrupt service routine. Upon completion of the interrupt
service routine, program execution resumes with the instruction immediately
following the instruction that activated Power-Down mode.
Note:
The external interrupt used to exit Power-Down mode must be configured as level sensi-
tive (INT0# and INT1#) and must be assigned the highest priority. In addition, the
duration of the interrupt must be long enough to allow the oscillator to stabilize. The exe-
cution will only resume when the interrupt is deasserted.
Note:
Exit from power-down by external interrupt does not affect the SFRs nor the internal RAM
content.
Figure 26. Power-Down Exit Waveform Using INT1:0#
2.
Generate a reset.
A logic high on the RST pin clears PD bit in PCON register directly and
asynchronously. This starts the oscillator and restores the clock to the CPU
and peripherals. Program execution momentarily resumes with the
instruction immediately following the instruction that activated Power-Down
mode and may continue for a number of clock cycles before the internal
reset algorithm takes control. Reset initializes the AT89C51ID2 and vectors
the CPU to address 0000h.
Note:
During the time that execution resumes, the internal RAM cannot be accessed; however,
it is possible for the Port pins to be accessed. To avoid unexpected outputs at the Port
INT1:0#
OSC
Power-down phase
Oscillator restart phase
Active phase
相關PDF資料
PDF描述
AT91SAM7X128B-CU IC MCU 128KB FLASH 100TFBGA
AT91SAM7XC128B-AU MCU ARM 128K HS FLASH 100-LQFP
ATSAM3U1CA-CU IC MCU 32BIT 64KB FLASH 100TFBGA
1981584-1 CONN RCPT MICRO USB TYPE AB
1981568-1 CONN RCPT MICRO USB B R/A SMD
相關代理商/技術參數
參數描述
AT89C51ID2-SMSIM 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Flash Microcontroller
AT89C51ID2-UM 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Flash Microcontroller
AT89C51RB2 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 16K/ 32K Bytes Flash
AT89C51RB2/RC2 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:AT89C51RB2/RC2 [Updated 4/03. 125 Pages]
AT89C51RB2_06 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 16K/ 32K Bytes Flash