參數資料
型號： AT32UC3A3-XPLD
廠商： Atmel
文件頁數： 81/94頁
文件大小： 0K
描述： KIT DEV/EVAL FOR AT32UC3A3
產品培訓模塊： AVR® UC3 Introduction
Sensors Xplained
標準包裝： 1
系列： AVR®32 UC3-A3 Xplained
類型： MCU
適用于相關產品： AT32UC3A3
所含物品： 板
82
32072SH–AVR32–10/2012
AT32UC3A3
Fix/Workaround
Before going to sleep modes where the system RC oscillator is stopped, make sure that the
factor between the CPU/HSB and PBx frequencies is less than or equal to 4.
10.2.9
PDCA
PCONTROL.CHxRES is non-functional
PCONTROL.CHxRES is non-functional. Counters are reset at power-on, and cannot be
reset by software.
Fix/Workaround
Software needs to keep history of performance counters.
Transfer error will stall a transmit peripheral handshake interface
If a transfer error is encountered on a channel transmitting to a peripheral, the peripheral
handshake of the active channel will stall and the PDCA will not do any more transfers on
the affected peripheral handshake interface.
Fix/Workaround
Disable and then enable the peripheral after the transfer error.
10.2.10
AES
URAD (Unspecified Register Access Detection Status) does not detect read accesses
to the write-only KEYW[5..8]R registers
Fix/Workaround
None.
10.2.11
HMATRIX
In the PRAS and PRBS registers, the MxPR fields are only two bits
In the PRAS and PRBS registers, the MxPR fields are only two bits wide, instead of four bits.
The unused bits are undefined when reading the registers.
Fix/Workaround
Mask undefined bits when reading PRAS and PRBS.
10.2.12
TWIM
TWIM SR.IDLE goes high immediately when NAK is received
When a NAK is received and there is a non-zero number of bytes to be transmitted,
SR.IDLE goes high immediately and does not wait for the STOP condition to be sent. This
does not cause any problem just by itself, but can cause a problem if software waits for
SR.IDLE to go high and then immediately disables the TWIM by writing a one to CR.MDIS.
Disabling the TWIM causes the TWCK and TWD pins to go high immediately, so the STOP
condition will not be transmitted correctly.
Fix/Workaround
If possible, do not disable the TWIM. If it is absolutely necessary to disable the TWIM, there
must be a software delay of at least two TWCK periods between the detection of
SR.IDLE==1 and the disabling of the TWIM.
TWIM TWALM polarity is wrong
The TWALM signal in the TWIM is active high instead of active low.
Fix/Workaround
Use an external inverter to invert the signal going into the TWIM. When using both TWIM
and TWIS on the same pins, the TWALM cannot be used.
相關PDF資料
PDF描述
GBC15DRTI-S734 CONN EDGECARD 30POS DIP .100 SLD
GBC19DRTH-S734 CONN EDGECARD 38POS DIP .100 SLD
AIUR-09-560M INDUCTOR POWER 56UH 20% T/H
AIUR-08-180K INDUCTOR POWER 18UH 10% T/H
GSC07DREI-S734 CONN EDGECARD 14POS .100 EYELET
相關代理商/技術參數
參數描述
AT32UC3A4128 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:32-bit AVR? Microcontroller
AT32UC3A4128-C1UR 功能描述:32位微控制器 - MCU 128k flash Ind RoHS:否 制造商:Texas Instruments 核心:C28x 處理器系列:TMS320F28x 數據總線寬度:32 bit 最大時鐘頻率:90 MHz 程序存儲器大小:64 KB 數據 RAM 大小:26 KB 片上 ADC:Yes 工作電源電壓:2.97 V to 3.63 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:LQFP-80 安裝風格:SMD/SMT
AT32UC3A4128-C1UT 功能描述:32位微控制器 - MCU 128k flash Ind RoHS:否 制造商:Texas Instruments 核心:C28x 處理器系列:TMS320F28x 數據總線寬度:32 bit 最大時鐘頻率:90 MHz 程序存儲器大小:64 KB 數據 RAM 大小:26 KB 片上 ADC:Yes 工作電源電壓:2.97 V to 3.63 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:LQFP-80 安裝風格:SMD/SMT
AT32UC3A4128HBZ-C1UR 制造商:Atmel Corporation 功能描述:128K FLASH 100 BALL TBGA REEL INDUSTRIAL - Tape and Reel
AT32UC3A4128S 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:32-bit AVR? Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*