參數資料
型號： ADUC812BCPZ-REEL
廠商： ANALOG DEVICES INC
元件分類： 微控制器/微處理器
英文描述： 8-BIT, FLASH, 11.0592 MHz, MICROCONTROLLER, PQCC56
封裝： LEAD FRAME, CSP-56
文件頁數： 58/60頁
文件大?。?/td> 1276K
代理商： ADUC812BCPZ-REEL
REV. E
ADuC812
–7–
PIN FUNCTION DESCRIPTIONS
Mnemonic
Type
Function
DVDD
PDigital Positive Supply Voltage, 3 V or 5 V Nominal.
AVDD
PAnalog Positive Supply Voltage, 3 V or 5 V Nominal.
CREF
IDecoupling Input for On-Chip Reference. Connect 0.1 F between this pin and AGND.
VREF
I/O
Reference Input/Output. This pin is connected to the internal reference through a series resistor and is the
reference source for the ADC. The nominal internal reference voltage is 2.5 V, which appears at the pin.
This pin can be overdriven by an external reference.
AGND
G
Analog Ground. Ground reference point for the analog circuitry.
P1.0–P1.7
I
Port 1 is an 8-bit input port only. Unlike other ports, Port 1 defaults to Analog Input mode. To configure
any of these Port Pins as a digital input, write a 0 to the port bit. Port 1 pins are multifunctional and share
the following functionality.
ADC0–ADC7
I
Analog Inputs. Eight single-ended analog inputs. Channel selection is via ADCCON2 SFR.
T2
I
Timer 2 Digital Input. Input to Timer/Counter 2. When enabled, Counter 2 is incremented in response to a
1 to 0 transition of the T2 input.
T2EX
I
Digital Input. Capture/Reload trigger for Counter 2; also functions as an Up/Down control input for
Counter 2.
SS
I
Slave Select Input for the SPI Interface.
SDATA
I/O
User selectable, I
2C Compatible or SPI Data Input/Output Pin.
SCLOCK
I/O
Serial Clock Pin for I
2C Compatible or SPI Serial Interface Clock.
MOSI
I/O
SPI Master Output/Slave Input Data I/O Pin for SPI Interface.
MISO
I/O
SPI Master Input/Slave Output Data I/O Pin for SPI Serial Interface.
DAC0
O
Voltage Output from DAC0.
DAC1
O
Voltage Output from DAC1.
RESET
I
Digital Input. A high level on this pin for 24 master clock cycles while the oscillator is running resets the
device. External power-on reset (POR) circuity must be implemented to drive the RESET pin as described
in the Power-On Reset Operation section.
P3.0–P3.7
I/O
Port 3 is a bidirectional port with internal pull-up resistors. Port 3 pins that have 1s written to them are
pulled high by the internal pull-up resistors; in that state they can be used as inputs. As inputs, Port 3 pins
being pulled externally low will source current because of the internal pull-up resistors. Port 3 pins also
contain various secondary functions that are described below.
RxD
I/O
Receiver Data Input (Asynchronous) or Data Input/Output (Synchronous) of Serial (UART) Port
TxD
O
Transmitter Data Output (Asynchronous) or Clock Output (Synchronous) of Serial (UART) Port
INT0
I
Interrupt 0, programmable edge or level triggered Interrupt input,
INT0 can be programmed to one of two
priority levels. This pin can also be used as a gate control input to Timer 0.
INT1
I
Interrupt 1, programmable edge or level triggered Interrupt input,
INT1 can be programmed to one of two
priority levels. This pin can also be used as a gate control input to Timer 1.
T0
I
Timer/Counter 0 Input.
T1
I
Timer/Counter 1 Input.
CONVST
I
Active Low Convert Start Logic Input for the ADC Block when the External Convert Start Function is Enabled.
A low-to-high transition on this input puts the track-and-hold into its hold mode and starts conversion.
WR
OWrite Control Signal, Logic Output. Latches the data byte from Port 0 into the external data memory.
RD
ORead Control Signal, Logic Output. Enables the external data memory to Port 0.
XTAL2
O
Output of the Inverting Oscillator Amplifier.
XTAL1
I
Input to the Inverting Oscillator Amplifier and to the Internal Clock Generator Circuits.
DGND
G
Digital Ground. Ground reference point for the digital circuitry.
P2.0–P2.7
I/O
Port 2 is a bidirectional port with internal pull-up resistors. Port 2 pins that have 1s written to them are
(A8–A15)
pulled high by the internal pull-up resistors; in that state they can be used as inputs. As inputs, Port 2
(A16–A23)
pins being pulled externally low will source current because of the internal pull-up resistors. Port 2 emits the
high order address bytes during fetches from external program memory and middle and high order address
bytes during accesses to the external 24-bit external data memory space.
相關PDF資料
PDF描述
ADUM1510BRWZ SPECIALTY ANALOG CIRCUIT, PDSO16
ADUM3210ARZ-RL7 SPECIALTY ANALOG CIRCUIT, PDSO8
AE101SD1AB TOGGLE SWITCH, SPDT, LATCHED, 0.02A, 20VDC, THROUGH HOLE-RIGHT ANGLE
AE103MD1CB TOGGLE SWITCH, SPDT, MOMENTARY, 0.02A, 20VDC, THROUGH HOLE-STRAIGHT
AE235RAA2N0JSW 1 ELEMENT, 0.002 uH, CERAMIC-CORE, GENERAL PURPOSE INDUCTOR, SMD
相關代理商/技術參數
參數描述
ADUC812BS 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 52-Pin MQFP 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 8KB FLASH 16MHZ 3.3/5V 52MQFP - Bulk 制造商:Analog Devices 功能描述:8BIT MCU +12BIT ADC MQFP52 812 制造商:Analog Devices 功能描述:Data Acquisition System, 8 Channel, 12 Bit, 52 Pin, Plastic, QFP
ADUC812BS 制造商:Analog Devices 功能描述:12-BIT ADC WITH EMBEDDED
aduc812bs-01 制造商:Analog Devices 功能描述:
ADUC812BS-REEL 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 52-Pin MQFP T/R
ADUC812BSZ 功能描述:IC ADC 12BIT MULTICH MCU 52-MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*