參數資料
型號： ADSP-TS203SABP-050
廠商： Analog Devices Inc
文件頁數： 4/48頁
文件大?。?/td> 0K
描述： IC DSP FLOAT/FIXED 500MHZ 576BGA
標準包裝： 1
系列： TigerSHARC®
類型： 定點/浮點
接口： 主機接口，連接端口，多處理器
時鐘速率： 500MHz
非易失內存： 外部
芯片上RAM： 512kB
電壓 - 輸入/輸出： 2.50V
電壓 - 核心： 1.05V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 576-BBGA 裸露焊盤
供應商設備封裝： 576-BGA-ED（25x25）
包裝： 托盤
其它名稱： ADSP-TS203SABP050
ADSP-TS203SABP050-ND
Rev. D
|
Page 12 of 48
|
May 2012
Table 5. Pin Definitions—External Port Bus Controls
Signal
Type
Term
Description
ADDR31–0
I/O/T
(pu_ad)
nc
Address Bus. The processor issues addresses for accessing memory and peripherals
on these pins. In a multiprocessor system, the bus master drives addresses for
accessing internal memory or I/O processor registers of other ADSP-TS203S
processors. The processor inputs addresses when a host or another processor
accesses its internal memory or I/O processor registers.
DATA31–0
I/O/T
(pu_ad)
nc
External Data Bus. The processor drives and receives data and instructions on these
pins. Pull-up or pull-down resistors on unused DATA pins are unnecessary.
RD
I/O/T
(pu_0)
epu1
Memory Read. RD is asserted whenever the processor reads from any slave in the
system, excluding SDRAM. When the processor is a slave, RD is an input and
indicates read transactions that access its internal memory or universal registers. In
a multiprocessor system, the bus master drives RD. RD changes concurrently with
ADDR pins.
WRL
I/O/T
(pu_0)
epu1
Write Low. WRL is asserted when the ADSP-TS203S processor writes to the external
bus (host, memory, or processor). An external master (host or processor) asserts WRL
for writing to a processor’s internal memory. In a multiprocessor system, the bus
master drives WRL. WRL changes concurrently with ADDR pins. When the processor
is a slave, WRL is an input and indicates write transactions that access its internal
memory or universal registers.
ACK
I/O/T/OD
(pu_od_0)
epu1
Acknowledge. External slave devices can deassert ACK to add wait states to external
memory accesses. ACK is used by I/O devices, memory controllers, and other periph-
erals on the data phase. The processor can deassert ACK to add wait states to read
and write accesses of its internal memory. The pull-up is 50 Ω on low-to-high trans-
actions and is 500 Ω on all other transactions.
BMS
O/T
(pu_0)
na
Boot Memory Select. BMS is the chip select for boot EPROM or flash memory. During
reset, the processor uses BMS as a strap pin (EBOOT) for EPROM boot mode. In a
multiprocessor system, the processor bus master drives BMS. For details, see Reset
and Booting on Page 8 and the EBOOT signal description in Table 16 on Page 18.
MS1–0
O/T
(pu_0)
nc
Memory Select. MS0 or MS1 is asserted whenever the processor accesses memory
banks 0 or 1, respectively. MS1–0 are decoded memory address pins that change
concurrently with ADDR pins. When ADDR31:27 = 0b00110, MS0 is asserted. When
ADDR31:27 = 0b00111, MS1 is asserted. In multiprocessor systems, the master
processor drives MS1–0.
MSH
O/T
(pu_0)
nc
Memory Select Host. MSH is asserted whenever the processor accesses the host
address space (ADDR31 = 0b1). MSH is a decoded memory address pin that changes
concurrently with ADDR pins. In a multiprocessor system, the bus master processor
drives MSH.
BRST
I/O/T
(pu_0)
Burst. The current bus master (processor or host) asserts this pin to indicate that it
is reading or writing data associated with consecutive addresses. A slave device can
ignore addresses after the first one and increment an internal address counter after
each transfer. For host-to-processor burst accesses, the processor increments the
address automatically while BRST is asserted.
TM4
I/O/T
epu
Test Mode 4. Must be pulled up to VDD_IO with a 5 kΩ resistor.
I = input; A = asynchronous; O = output; OD = open-drain output; T = three-state; P = power supply; G = ground; pd = internal pull-down
5kΩ; pu = internal pull-up 5 kΩ; pd_0 = internal pull-down 5 kΩ on processor ID = 0; pu_0 = internal pull-up 5 kΩ on processor ID = 0;
pu_od_0 = internal pull-up 500 Ω on processor ID = 0; pd_m = internal pull-down 5 kΩ on processor bus master; pu_m = internal pull-up
5 kΩ on processor bus master; pu_ad = internal pull-up 40 kΩ. For more pull-down and pull-up information, see Electrical Characteristics
Term (termination of unused pins) column symbols: epd = external pull-down approximately 5 kΩ to VSS; epu = external pull-up
approximately 5 kΩ to VDD_IO, nc = not connected; na = not applicable (always used); VDD_IO = connect directly to VDD_IO; VSS = connect
directly to VSS
1 This external pull-up may be omitted for the ID = 000 TigerSHARC processor.
相關PDF資料
PDF描述
ADUC7021BCPZ62-RL7 IC MCU 12BIT 1MSPS UART 40-LFCSP
ADUC7023BCPZ62I-R7 IC MCU 12BIT 62KB FLASH 32LFCSP
ADUC7024BCPZ62 IC MCU FLSH 62K ANLG I/O 64LFCSP
ADUC7032BSTZ-88 IC MCU 96K FLASH DUAL 48LQFP
ADUC7032BSTZ-8V-RL IC BATTERY SENSOR PREC 48-LQFP
相關代理商/技術參數
參數描述
ADSP-TS203SABP-05X 制造商:Analog Devices 功能描述:
ADSP-TS203SABPZ050 功能描述:IC PROCESSOR 500MHZ 576BGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:TigerSHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
ADSP-TS203SBBPZ050 制造商:Analog Devices 功能描述:DSP - Bulk
ADSQ-1410 制造商:MURATA-PS 制造商全稱:Murata Power Solutions Inc. 功能描述:Quad 14-Bit, 10 MSPS Sampling A/D Converter
ADSQ-1410-C 制造商:MURATA-PS 制造商全稱:Murata Power Solutions Inc. 功能描述:Quad 14-Bit, 10 MSPS Sampling A/D Converter
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*