參數資料
型號： ADSP-BF542KBCZ-6A
廠商： ANALOG DEVICES INC
元件分類： 數字信號處理
英文描述： 600 MHz Blackfin Embedded Processor: ADSP-BF542KBCZ-6A Temp Range: 0°C to +70°C Package: 400-Ball CSP_BGA BC-400-1
中文描述： 16-BIT, 50 MHz, OTHER DSP, PBGA400
封裝： 17 X 17 MM, ROHS COMPLIANT, CSBGA-400
文件頁數： 7/100頁
文件大小： 3095K
代理商： ADSP-BF542KBCZ-6A
Rev. D
|
Page 14 of 100
|
May 2011
ADSP-BF542/ADSP-BF544/ADSP-BF547/ADSP-BF548/ADSP-BF549
The USB clock (USB_XI) is provided through a dedicated exter-
nal crystal or crystal oscillator. See Table 62 for related timing
requirements. If using a fundamental mode crystal to provide
the USB clock, connect the crystal between USB_XI and
USB_XO with a circuit similar to that shown in Figure 7. Use a
parallel-resonant, fundamental mode, microprocessor-grade
crystal. If a third-overtone crystal is used, follow the circuit
guidelines outlined in Clock Signals on Page 17 for third-over-
tone crystals.
The USB On-the-Go dual-role device controller includes a
Phase Locked Loop with programmable multipliers to generate
the necessary internal clocking frequency for USB. The multi-
plier value should be programmed based on the USB_XI clock
frequency to achieve the necessary 480 MHz internal clock for
USB high speed operation. For example, for a USB_XI crystal
frequency of 24 MHz, the USB_PLLOSC_CTRL register should
be programmed with a multiplier value of 20 to generate a 480
MHz internal clock.
ATA/ATAPI-6 INTERFACE
The ATAPI interface connects to CD/DVD and HDD drives
and is ATAPI-6 compliant. The controller implements the
peripheral I/O mode, the multi-DMA mode, and the Ultra
DMA mode. The DMA modes enable faster data transfer and
reduced host management. The ATAPI controller supports
PIO, multi-DMA, and ultra DMA ATAPI accesses. Key features
include:
Supports PIO modes 0, 1, 2, 3, 4
Supports multiword DMA modes 0, 1, 2
Supports ultra DMA modes 0, 1, 2, 3, 4, 5 (up to UDMA
100)
Programmable timing for ATA interface unit
Supports CompactFlash cards using true IDE mode
By default, the ATAPI_A0-2 address signals and the
ATAPI_D0-15 data signals are shared on the asynchronous
memory interface with the asynchronous memory and NAND
flash controllers. The data and address signals can be remapped
to GPIO ports F and G, respectively, by setting
PORTF_MUX[1:0] to b#01.
KEYPAD INTERFACE
The keypad interface is a 16-pin interface module that is used to
detect the key pressed in a 8 × 8 (maximum) keypad matrix. The
size of the input keypad matrix is programmable. The interface
is capable of filtering the bounce on the input pins, which is
common in keypad applications. The width of the filtered
bounce is programmable. The module is capable of generating
an interrupt request to the core once it identifies that any key
has been pressed.
The interface supports a press-release-press mode and infra-
structure for a press-hold mode. The former mode identifies a
press, release and press of a key as two consecutive presses of the
same key, whereas the latter mode checks the input key’s state in
periodic intervals to determine the number of times the same
key is meant to be pressed. It is possible to detect when multiple
keys are pressed simultaneously and to provide limited key reso-
lution capability when this happens.
SECURE DIGITAL (SD)/SDIO CONTROLLER
The SD/SDIO controller is a serial interface that stores data at a
data rate of up to 10M bytes per second using a 4-bit data line.
The SD/SDIO controller supports the SD memory mode only.
The interface supports all the power modes and performs error
checking by CRC.
CODE SECURITY
An OTP/security system, consisting of a blend of hardware and
software, provides customers with a flexible and rich set of code
security features with Lockbox
secure technology. Key features
include:
OTP memory
Unique chip ID
Code authentication
Secure mode of operation
The security scheme is based upon the concept of authentica-
tion of digital signatures using standards-based algorithms and
provides a secure processing environment in which to execute
code and protect assets. See Lockbox Secure Technology Dis-
MEDIA TRANSCEIVER MAC LAYER (MXVR)
The ADSP-BF549 Blackfin processors provide a media trans-
ceiver (MXVR) MAC layer, allowing the processor to be
connected directly to a MOST
1 network through an FOT. See
Figure 5 on Page 15 for an example of a MXVR MOST
connection.
The MXVR is fully compatible with industry-standard stand-
alone MOST controller devices, supporting 22.579 Mbps or
24.576 Mbps data transfer. It offers faster lock times, greater jit-
ter immunity, and a sophisticated DMA scheme for data
transfers. The high speed internal interface to the core and L1
memory allows the full bandwidth of the network to be utilized.
The MXVR can operate as either the network master or as a net-
work slave.
The MXVR supports synchronous data, asynchronous packets,
and control messages using dedicated DMA channels that oper-
ate autonomously from the processor core moving data to and
from L1 and/or L2 memory. Synchronous data is transferred to
or from the synchronous data physical channels on the MOST
bus through eight programmable DMA channels. The synchro-
nous data DMA channels can operate in various modes
including modes that trigger DMA operation when data pat-
terns are detected in the receive data stream. Furthermore, two
DMA channels support asynchronous traffic, and two others
support control message traffic.
1 MOST is a registered trademark of Standard Microsystems, Corp.
相關PDF資料
PDF描述
ADSP-BF544BBCZ-4A 400 MHz Blackfin Embedded Processor: ADSP-BF544BBCZ-4A Temp Range: –40°C to +85°C Package: 400-Ball CSP_BGA BC-400-1
ADSP-BF544BBCZ-5A 533 MHz Blackfin Embedded Processor: ADSP-BF544BBCZ-5A Temp Range: –40°C to +85°C Package: 400-Ball CSP_BGA BC-400-1
ADSP-BF544MBBCZ-5M 533 MHz Blackfin Embedded Processor: ADSP-BF544MBBCZ-5M Temp Range: –40°C to +85°C Package: 400-Ball CSP_BGA BC-400-1
ADSP-BF547BBCZ-5A 533 MHz Blackfin Embedded Processor: ADSP-BF547BBCZ-5A Temp Range: –40°C to +85°C Package: 400-Ball CSP_BGA BC-400-1
ADSP-BF547MBBCZ-5M 533 MHz Blackfin Embedded Processor: ADSP-BF547MBBCZ-5M Temp Range: –40°C to +85°C Package: 400-Ball CSP_BGA BC-400-1
相關代理商/技術參數
參數描述
ADSP-BF542MBBCZ-5M 功能描述:IC DSP 16BIT 533MHZ MDDR 400CBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:Blackfin® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
ADSP-BF544BBCZ-4A 功能描述:IC CCD SIGNAL PROCESSOR 400BGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:Blackfin® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
ADSP-BF544BBCZ-5A 功能描述:IC DSP 16BIT 533MHZ 400CSBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:Blackfin® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
ADSP-BF544BBCZ-5X 制造商:Analog Devices 功能描述:HIGH PERFORMANCE CONVERGENT MULTIMEDIA BLACKFIN PROCESSOR - Trays
ADSP-BF544MBBCZ-5M 功能描述:IC DSP 16BIT 533MHZ MDDR 400CBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:Blackfin® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*