- 您現在的位置：買賣IC網 > PDF目錄374016 > ADM9240ARU (ANALOG DEVICES INC) Low Cost Microprocessor System Hardware Monitor PDF資料下載
參數資料
| 型號： | ADM9240ARU |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 電源管理 |
| 英文描述： | Low Cost Microprocessor System Hardware Monitor |
| 中文描述： | 9-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO24 |
| 封裝： | TSSOP-24 |
| 文件頁數： | 6/22頁 |
| 文件大?。?/td> | 280K |
| 代理商： | ADM9240ARU |
ADM9240
–6–
REV. 0
GE NE RAL DE SCRIPT ION
T he ADM9240 is a complete system hardware monitor for
microprocessor-based systems. T he device communicates with
the system via a serial System Management Bus. T he serial bus
controller has two hardwired address lines for device selection
(Pin 1 and Pin 2), a serial data line for reading and writing
addresses and data (Pin 3), and an input line for the serial clock
(Pin 4). All control and programming functions of the ADM9240
are performed over the serial bus.
An on-chip analog-to-digital converter with six multiplexed
analog inputs measures power supply voltages (+12 V, +5 V,
+3.3 V, +2.5 V—Pins 15 to 18) and processor core voltages
(+V
CCP1
and +V
CCP2
—Pins 19 and 14). T he ADC also accepts
input from an on-chip bandgap temperature sensor that moni-
tors system ambient temperature.
T wo count inputs (Pins 5 and 6) are provided for monitoring
the speed of fans with tachometer outputs. T o accommodate
fans with different speeds and different tacho outputs, a divisor
of 1, 2, 4 or 8 can be programmed into the counter.
Five digital inputs (VID4 to VID0—Pins 20 to 24) read the
processor Voltage ID code, while a chassis intrusion input
(Pin 7) is provided to detect unauthorized tampering with the
equipment.
When the ADM9240 monitoring sequence is started, it cycles
sequentially through the measurement of analog inputs and the
temperature sensor, while at the same time the fan speed inputs
are independently monitored. Measured values from these in-
puts are stored in value registers. T hese can be read out over the
serial bus, or can be compared with programmed limits stored
in the limit registers. T he results of out-of-limit comparisons are
stored in the interrupt status registers and will generate an inter-
rupt on the
INT
line (Pin 10).
Any or all of the Interrupt Status Bits can be masked by appro-
priate programming of the Interrupt Mask Register.
A
RESET
input/output (Pin 12) is provided. Pulling this pin
low will reset all ADM9240 internal registers to default values.
T he ADM9240 can also be programmed to give a low-going
20 ms reset pulse at this pin.
T he ADM9240 contains an on-chip, 8-bit digital-to-analog
converter with an output range of zero to 1.25 V (Pin 11). T his
is typically used to implement a temperature-controlled fan by
controlling the speed of a fan dependent upon the temperature
measured by the on-chip temperature sensor.
T esting of board level connectivity is simplified by providing a
NAND tree test function. T he AOUT (Pin 11) also doubles as
a NAND test input, while Pin 1 doubles as a NAND tree output.
INT E RNAL RE GIST E RS OF T HE ADM9240
A brief description of the ADM9240’s principal internal regis-
ters is given below. More detailed information on the function
of each register is given in T ables V to X VII.
Configuration Register:
Provides control and configuration.
Serial Address Register:
Stores the serial bus address of the
ADM9240.
Address Pointer Register:
Contains the address that selects
one of the other internal registers. When writing to the ADM9240,
the first byte of data is always a register address, which is written
to the Address Pointer Register.
Interrupt (INT ) Status Registers:
T wo registers to provide
status of each Interrupt event.
Interrupt (INT ) Mask Registers:
Allow masking of indi-
vidual Interrupt sources.
T emperature Configuration Register:
T he configuration of
the temperature interrupt is controlled by the lower three bits of
this register.
VID/Fan Divisor Registers:
T he status of the VID0 to VID4
pins of the processor can be written to and read from these
registers. Divisor values for fan-speed measurement are also
stored in one of these registers.
Value and Limit Registers:
T he results of analog voltage
inputs, temperature and fan speed measurements are stored in
these registers, along with their limit values.
Analog Output Register:
T he code controlling the analog
output DAC is stored in this register.
Chassis Intrusion Clear Register:
A signal latched on the
chassis intrusion pin can be cleared by writing to this register.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM9261 | Triple- Power Supply Monitor(3路電源監視器) |
| ADM9264ARN-REEL | Quad Power Supply Monitor for Desktop PCs |
| ADM9264ARN-REEL7 | Quad Power Supply Monitor for Desktop PCs |
| ADM9264 | Quad Power Supply Monitor for Desktop PCs |
| ADM9264ARN | Quad Power Supply Monitor for Desktop PCs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM9240ARU-REEL | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost Microprocessor System Hardware Monitor |
| ADM9240ARU-REEL7 | 制造商:Analog Devices 功能描述: |
| ADM9264 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad Power Supply Monitor for Desktop PCs |
| ADM9264ARN | 制造商:Analog Devices 功能描述:Volt Supervisor Monitor 2.8V/3.3V/5V/12V 16-Pin SOIC N 制造商:Rochester Electronics LLC 功能描述:MULTI-SUPPLY HARDWARE MON - Bulk |
| ADM9264ARN-REEL | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。