- 您現在的位置：買賣IC網 > PDF目錄1895 > AD9985KSTZ-140 (Analog Devices Inc)IC INTERFACE 8BIT 140MSPS 80LQFP PDF資料下載
參數資料
| 型號： | AD9985KSTZ-140 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 24/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC INTERFACE 8BIT 140MSPS 80LQFP |
| 產品變化通告： | Product Discontinuance 27/Oct/2011 |
| 標準包裝： | 90 |
| 應用： | 視頻 |
| 接口： | 串行 |
| 電源電壓： | 2.2 V ~ 3.45 V |
| 封裝/外殼： | 80-LQFP |
| 供應商設備封裝： | 80-LQFP（14x14） |
| 包裝： | 管件 |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD9985
Rev. 0 | Page 30 of 32
PLL
Place the PLL loop filter components as close to the FILT pin as
possible.
Do not place any digital or other high frequency traces near
these components.
Use the values suggested in the data sheet with 10% tolerances
or less.
OUTPUTS (BOTH DATA AND CLOCKS)
Try to minimize the trace length that the digital outputs have to
drive. Longer traces have higher capacitance, which requires
more current, which causes more internal digital noise.
Shorter traces reduce the possibility of reflections.
Adding a series resistor of value 22 to 100 can suppress
reflections, reduce EMI, and reduce the current spikes inside of
the AD9985. However, if 50 traces are used on the PCB, the
data outputs should not need resistors. A 22 resistor on the
DATACK output should provide good impedance matching
that will reduce reflections. If series resistors are used, place
them as close to the AD9985 pins as possible (although try not
to add vias or extra length to the output trace in order to get the
resistors closer).
If possible, limit the capacitance that each of the digital outputs
drives to less than 10 pF. This can easily be accomplished by
keeping traces short and by connecting the outputs to only one
device. Loading the outputs with excessive capacitance will
increase the current transients inside of the AD9985, creating
more digital noise on its power supplies.
DIGITAL INPUTS
The digital inputs on the AD9985 were designed to work with
3.3 V signals, but are tolerant of 5.0 V signals. Therefore, no
extra components need to be added if using 5.0 V logic.
Any noise that gets onto the Hsync input trace will add jitter to
the system. Therefore, minimize the trace length and do not run
any digital or other high frequency traces near it.
VOLTAGE REFERENCE
Bypass with a 0.1 F capacitor. Place as close to the AD9985 pin
as possible. Make the ground connection as short as possible.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9990BBCZ | IC CCD SGNL PROCESSOR 112CSPBGA |
| AD9991KCPZRL | IC CCD SIGNAL PROCESSOR 56-LFCSP |
| AD9992BBCZRL | IC CCD SGNL PROC 12BIT 105CSPBGA |
| AD9995KCPZ | IC CCD SIGNAL PROCESSOR 56-LFCSP |
| ADA4424-6ARUZ | IC FILTR VID6CH SD/ED/HD 38TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9990 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual Channel, 14-Bit CCD Signal Processor with V-Driver and Precision Timing |
| AD9990BBCZ | 功能描述:IC CCD SGNL PROCESSOR 112CSPBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD9990BBCZRL | 功能描述:IC CCD SGNL PROCESSOR 112CSPBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD9991 | 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit CCD Signal Processor with Precision Timing Generator |
| AD9991KCP | 制造商:Analog Devices 功能描述:AFE Video 1ADC 10-Bit 3V 56-Pin LFCSP EP 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。