參數資料
型號: AD9985KSTZ-140
廠商: Analog Devices Inc
文件頁數: 16/32頁
文件大?。?/td> 0K
描述: IC INTERFACE 8BIT 140MSPS 80LQFP
產品變化通告: Product Discontinuance 27/Oct/2011
標準包裝: 90
應用: 視頻
接口: 串行
電源電壓: 2.2 V ~ 3.45 V
封裝/外殼: 80-LQFP
供應商設備封裝: 80-LQFP(14x14)
包裝: 管件
安裝類型: 表面貼裝
AD9985
Rev. 0 | Page 23 of 32
10
2
Red Clamp Select
This bit determines whether the Red channel is
clamped to ground or to midscale. For RGB video, all
three channels are referenced to ground. For YCbCr
(or YUV), the Y channel is referenced to ground, but
the CbCr channels are referenced to midscale.
Clamping to midscale actually clamps to Pin 37.
Table 28. Red Clamp Select Settings
Clamp
Function
0
Clamp to Ground
1
Clamp to Midscale (Pin 37)
The default setting for this register is 0.
10
1
Green Clamp Select
This bit determines whether the Green channel is
clamped to ground or to midscale.
Table 29. Green Clamp Select Settings
Clamp
Function
0
Clamp to Ground
1
Clamp to Midscale (Pin 37)
The default setting for this register is 0.
10
0
Blue Clamp Select
This bit determines whether the Blue channel is
clamped to ground or to midscale.
Table 30. Blue Clamp Select Settings
Clamp
Function
0
Clamp to Ground
1
Clamp to Midscale (Pin 37)
The default for this register is 0.
11
7–0
Sync Separator Threshold
This register is used to set the responsiveness of the
sync separator. It sets how many internal 5 MHz clock
periods the sync separator must count to before
toggling high or low. It works like a low-pass filter to
ignore Hsync pulses in order to extract the Vsync
signal. This register should be set to some number
greater than the maximum Hsync pulsewidth. Note
that the sync separator threshold uses an internal
dedicated clock with a frequency of approximately
5 MHz.
The default for this register is 32.
12
7–0
Pre-Coast
This register allows the coast signal to be applied prior
to the Vsync signal. This is necessary in cases where
pre-equalization pulses are present. The step size for
this control is one Hsync period.
The default is 0.
13
7–0
Post-Coast
This register allows the coast signal to be applied
following the Vsync signal. This is necessary in cases
where post-equalization pulses are present. The step
size for this control is one Hsync period.
The default is 0.
14
7
Hsync Detect
This bit is used to indicate when activity is detected on
the Hsync input pin (Pin 30). If Hsync is held high or
low, activity will not be detected.
Table 31. Hsync Detection Results
Detect
Function
0
No Activity Detected
1
Activity Detected
The Sync Processing Block Diagram (Figure 14) shows
where this function is implemented.
14
6
AHS – Active Hsync
This bit indicates which Hsync input source is being
used by the PLL (Hsync input or Sync-on-Green).
Bits 7 and 1 in this register determine which source is
used. If both Hsync and SOG are detected, the user
can determine which has priority via Bit 3 in
Register 0EH. The user can override this function via
Bit 4 in Register 0EH. If the override bit is set to
Logic 1, this bit will be forced to whatever the state of
Bit 3 in Register 0EH is set to.
Table 32. Active Hsync Results
Bit 7
Bit 1
Bit 4,
(Hsync
(SOG
Reg 0EH
Detect)
(Override)
AHS
0
Bit 3 in 0EH
0
1
0
1
0
1
0
Bit 3 in 0EH
X
1
Bit 3 in 0EH
AHS = 0 means use the Hsync pin input for Hsync.
AHS = 1 means use the SOG pin input for Hsync.
The override bit is in Register 0EH, Bit 4.
14
5
Detected Hsync Input Polarity Status
This bit reports the status of the Hsync input polarity
detection circuit. It can be used to determine the
polarity of the Hsync input. The detection circuit’s
location is shown in the Sync Processing Block
Diagram (Figure 14).
相關PDF資料
PDF描述
AD9990BBCZ IC CCD SGNL PROCESSOR 112CSPBGA
AD9991KCPZRL IC CCD SIGNAL PROCESSOR 56-LFCSP
AD9992BBCZRL IC CCD SGNL PROC 12BIT 105CSPBGA
AD9995KCPZ IC CCD SIGNAL PROCESSOR 56-LFCSP
ADA4424-6ARUZ IC FILTR VID6CH SD/ED/HD 38TSSOP
相關代理商/技術參數
參數描述
AD9990 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual Channel, 14-Bit CCD Signal Processor with V-Driver and Precision Timing
AD9990BBCZ 功能描述:IC CCD SGNL PROCESSOR 112CSPBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG,串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:20-TSSOP 包裝:管件
AD9990BBCZRL 功能描述:IC CCD SGNL PROCESSOR 112CSPBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG,串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:20-TSSOP 包裝:管件
AD9991 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit CCD Signal Processor with Precision Timing Generator
AD9991KCP 制造商:Analog Devices 功能描述:AFE Video 1ADC 10-Bit 3V 56-Pin LFCSP EP 制造商:Rochester Electronics LLC 功能描述:- Bulk