參數資料
型號： AD974
廠商： Analog Devices, Inc.
英文描述： 4-Channel, 16-Bit, 200 kSPS Data Acquisition System
中文描述： 4通道，16位，200 kSPS的數據采集系統
文件頁數： 5/20頁
文件大?。?/td> 202K
代理商： AD974
REV. A
AD974
–5–
PIN FUNCTION DESCRIPTIONS
Pin No.
Mnemonic
Description
1
2–5, 25–28
6
7
AGND1
VxA, VxB
BIP
CAP
Analog Ground. Used as the ground reference point for the REF pin.
Analog Input. Refer to Table I for input range configuration.
Bipolar Offset. Connect VxA inputs to provide Bipolar input range.
Reference Buffer Output. Connect a 2.2
μ
F tantalum capacitor between CAP and Analog
Ground.
Reference Input/Output. The internal +2.5 V reference is available at this pin. Alternatively an
external reference can be used to override the internal reference. In either case, connect a 2.2
μ
F
tantalum capacitor between REF and Analog Ground.
Analog Ground.
Read/
Convert
Input. Used to control the conversion and read modes. With
CS
LOW, a falling
edge on R/
C
holds the analog input signal internally and starts a conversion; a rising edge enables
the transmission of the conversion result.
Digital Power Supply. Nominally +5 V.
Power-Down Input. When set to a logic HIGH, power consumption is reduced and conversions
are inhibited. The conversion result from the previous conversion is stored in the onboard shift
register.
Digital select input for choosing the internal or an external data clock. With EXT/
INT
tied LOW,
after initiating a conversion, 16 DATACLK pulses transmit the previous conversion result as
shown in Figure 3. With EXT/
INT
set to a Logic HIGH, output data is synchronized to an
external clock signal connected to the DATACLK input. Data is output as indicated in Figure 4
through Figure 9.
Digital Ground.
Digital output frame synchronization for use with an external data clock (EXT/
INT
= Logic
HIGH). When a read sequence is initiated, a pulse one DATACLK period wide is output
synchronous to the external data clock.
Serial data clock input or output, dependent upon the logic state of the EXT/
INT
pin. When
using the internal data clock (EXT/
INT
= Logic LOW), a conversion start sequence will initiate
transmission of 16 DATACLK periods. Output data is synchronous to this clock and is valid on
both its rising and falling edges (Figure 3). When using an external data clock (EXT/
INT
= Logic
HIGH), the
CS
and R/
C
signals control how conversion data is accessed.
The serial data output is synchronized to DATACLK. Conversion results are stored in an on-
chip register. The AD974 provides the conversion result, MSB first, from its internal shift regis-
ter. When using the internal data clock (EXT/
INT
= Logic LOW), DATA is valid on both the
rising and falling edges of DATACLK. Using an external data clock (EXT/
INT
= Logic HIGH)
allows previous conversion data to be accessed during a conversion (Figures 5, 7 and 9) or the
conversion result can be accessed after the completion of a conversion (Figures 4, 6 and 8).
Multiplexer Write Inputs. These inputs are internally ORed to generate the mux latch inputs.
The latch is transparent when
WR1
and
WR2
are tied low.
Chip Select Input. With R/
C
LOW, a falling edge on
CS
will initiate a conversion. With R/
C
HIGH, a falling edge on
CS
will enable the serial data output sequence.
Busy Output. Goes LOW when a conversion is started, and remains LOW until the conversion is
completed and the data is latched into the on-chip shift register.
Address multiplexer inputs latched with the
WR1
,
WR2
inputs.
8
REF
9
10
AGND2
R/
C
11
12
V
DIG
PWRD
13
EXT/
INT
14
15
DGND
SYNC
16
DATACLK
17
DATA
18, 19
WR1
,
WR2
20
CS
21
BUSY
22, 23
A1, A0
A1
A0
Data Available from Channel
0
0
1
1
0
1
0
1
AIN 1
AIN 2
AIN 3
AIN 4
24
V
ANA
Analog Power Supply. Nominally +5 V.
相關PDF資料
PDF描述
AD974AN 4-Channel, 16-Bit, 200 kSPS Data Acquisition System
AD974AR 4-Channel, 16-Bit, 200 kSPS Data Acquisition System
AD974BN 4-Channel, 16-Bit, 200 kSPS Data Acquisition System
AD974BR 4-Channel, 16-Bit, 200 kSPS Data Acquisition System
AD974BRS 4-Channel, 16-Bit, 200 kSPS Data Acquisition System
相關代理商/技術參數
參數描述
AD9740 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit, 165 MSPS TxDAC D/A Converter
AD9740ACP 制造商:Analog Devices 功能描述:DAC 1-CH Segment 10-bit 32-Pin LFCSP EP 制造商:Rochester Electronics LLC 功能描述:10 BIT 165 MSPS TXDAC D/A CONVERTER - Bulk
AD9740ACP-PCB 制造商:Analog Devices 功能描述:Evaluation Board For 10Bit, 165MSPS TxDAC D/A Converters 制造商:Analog Devices 功能描述:DEV TOOLS, 10BIT, 165MSPS TXDAC D/A CNVRTRS - Bulk
AD9740ACP-PCBZ 功能描述:BOARD EVAL FOR AD9740ACP RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:TxDAC® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
AD9740ACPRL7 制造商:Analog Devices 功能描述:DAC 1-CH Segment 10-bit 32-Pin LFCSP EP T/R
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*