- 您現在的位置：買賣IC網 > PDF目錄1893 > AD8191AASTZ (Analog Devices Inc)IC HDMI/DVI SWITCH 4:1 100LQFP PDF資料下載
參數資料
| 型號： | AD8191AASTZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 16/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC HDMI/DVI SWITCH 4:1 100LQFP |
| 標準包裝： | 1 |
| 功能： | 開關，DVI/HDMI |
| 電路： | 1 x 16:1 |
| 電壓電源： | 單電源 |
| 電壓 - 電源，單路/雙路(±)： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-LQFP |
| 供應商設備封裝： | 100-LQFP（14x14） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD8191A
Rev. 0 | Page 23 of 28
CABLE LENGTHS AND EQUALIZATION
The AD8191A offers two levels of programmable equalization
for the high speed inputs: 6 dB and 12 dB. The equalizer of the
AD8191A supports video data rates of 1.65 Gbps. It can
equalize up to 20 meters of 24 AWG HDMI cable at data rates
corresponding to the video format, 1080p.
The length of cable that can be used in a typical HDMI/DVI
application depends on a large number of factors, including:
Cable quality: the quality of the cable in terms of conductor
wire gauge and shielding. Thicker conductors have lower
signal degradation per unit length.
Data rate: the data rate being sent over the cable. The signal
degradation of HDMI cables increases with data rate.
Edge rates: the edge rates of the source input. Slower input
edges result in more significant data eye closure at the end
of a cable.
Receiver sensitivity: the sensitivity of the terminating
receiver.
As such, specific cable types and lengths are not recommended
for use with a particular equalizer setting. In nearly all applica-
tions, the AD8191A equalization level can be set to high, or 12 dB,
for all input cable configurations at all data rates, without degrading
the signal integrity.
PCB LAYOUT GUIDELINES
The AD8191A is used to switch two distinctly different types
of signals, both of which are required for HDMI and DVI video.
These signal groups require different treatment when laying
out a PCB.
The first group of signals carries the audiovisual (AV) data. HDMI/
DVI video signals are differential, unidirectional, and high speed
(up to 1.65 Gbps). The channels that carry the video data must
be controlled impedance, terminated at the receiver, and capable
of operating up to at least 1.65 Gbps. It is especially important
to note that the differential traces that carry the TMDS signals
should be designed with a controlled differential impedance of
100 Ω. The AD8191A provides single-ended, 50 Ω terminations
on-chip for both its inputs and outputs, and both the input and
output terminations can be enabled or disabled through the
serial interface. Transmitter termination is not fully specified by
the HDMI standard but its inclusion improves the overall system
signal integrity.
The audiovisual data carried on these high speed channels are
encoded by a technique called transmission minimized differential
signaling (TMDS) and, in the case of HDMI, is also encrypted
according to the high bandwidth digital copy protection (HDCP)
standard.
The second group of signals consists of low speed auxiliary
control signals used for communication between a source and a
sink. Depending upon the application, these signals can include
the DDC bus (an I2C bus used to send EDID information and
HDCP encryption keys between the source and the sink), the
consumer electronics control (CEC) line, and the hot plug
detect (HPD) line. These auxiliary signals are bidirectional, low
speed, and transferred over a single-ended transmission line
that does not need to have controlled impedance. The primary
concern with laying out the auxiliary lines is ensuring that they
conform to the I2C bus standard and do not have excessive
capacitive loading.
TMDS Signals
In the HDMI/DVI standard, four differential pairs carry the
TMDS signals. In DVI, three of these pairs are dedicated to
carrying RGB video and sync data. For HDMI, audio data is
interleaved with the video data; the DVI standard does not
incorporate audio information. The fourth high speed differential
pair is used for the AV data-word clock and runs at one-tenth
the speed of the TMDS data channels.
The four high speed channels of the AD8191A are identical.
No concession was made to lower the bandwidth of the fourth
channel for the pixel clock; therefore, any channel can be used
for any TMDS signal. The user chooses which signal is routed
over which channel. Additionally, the TMDS channels are
symmetrical; therefore, the p and n of a given differential pair
are interchangeable, provided the inversion is consistent across
all inputs and outputs of the AD8191A. However, the routing
between inputs and outputs through the AD8191A is fixed.
The AD8191A buffers the TMDS signals and the input traces
can be considered electrically independent of the output traces.
In most applications, the quality of the signal on the input TMDS
traces is more sensitive to the PCB layout. Regardless of the data
being carried on a specific TMDS channel, or whether the TMDS
line is at the input or the output of the AD8191A, all four high
speed signals should be routed on a PCB in accordance with the
same RF layout guidelines.
Layout for the TMDS Signals
The TMDS differential pairs can be either microstrip traces,
routed on the outer layer of a board, or stripline traces, routed
on an internal layer of the board. If microstrip traces are used,
there should be a continuous reference plane on the PCB layer
directly below the traces. If stripline traces are used, they must
be sandwiched between two continuous reference planes in the
PCB stack-up.
相關PDF資料 |
PDF描述 |
|---|---|
| AD8191ASTZ | IC INTERFACE HDMI/DVI 100-LQFP |
| AD8192ACPZ-RL7 | IC SW MUX HDMI/DVI 2:1 56LFCSP |
| AD8193ACPZ | IC SWITCH TMDS BUFF 2:1 32LFCSP |
| AD8194ACPZ-R7 | IC SWITCH TMDS BUFF 2:1 32LFCSP |
| AD8195ACPZ | IC BUFF HDMI/DVI W/EQUAL 40LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8191AASTZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:4:1 HDMI/DVI Switch with Equalization |
| AD8191AASTZ-RL | 功能描述:IC SWITCH HDMI/DVI 4:1 100LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 其它有關文件:STG4159 View All Specifications 標準包裝:5,000 系列:- 功能:開關 電路:1 x SPDT 導通狀態電阻:300 毫歐 電壓電源:雙電源 電壓 - 電源，單路/雙路(±):±1.65 V ~ 4.8 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:7-WFBGA，F(xiàn)CBGA 供應商設備封裝:7-覆晶 包裝:帶卷 (TR) |
| AD8191AASTZ-RL1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:4:1 HDMI/DVI Switch with Equalization |
| AD8191ACPZ | 制造商:Analog Devices 功能描述:- Bulk |
| AD8191A-EVALZ | 制造商:Analog Devices 功能描述:EVAL BD FOR AD8191A - Bulk |
發布緊急采購，3分鐘左右您將得到回復。