- 您現在的位置：買賣IC網 > PDF目錄2062 > AD7148ACPZ-1REEL (Analog Devices Inc)IC CAP-TO-DGTL CONV PROG 16LFCSP PDF資料下載
參數資料
| 型號： | AD7148ACPZ-1REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 9/57頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CAP-TO-DGTL CONV PROG 16LFCSP |
| 標準包裝： | 5,000 |
| 類型： | 電容性 |
| 觸摸面板接口： | 2 線 |
| 輸入數/鍵： | 8 鍵 |
| 分辨率（位）： | 16 b |
| 數據接口： | I²C，串行 |
| 數據速率/采樣率 (SPS，BPS)： | 250k |
| 電壓基準： | 內部 |
| 電源電壓： | 2.6 V ~ 3.3 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-VQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 16-LFCSP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
AD7148
Rev. A | Page 16 of 56
CAPACITANCE SENSOR INPUT CONFIGURATION
Each input connection from the external capacitance sensors to
the AD7148 converter can be uniquely configured by using the
are used to configure input pin connection setups, sensor offsets,
sensor sensitivities, and sensor limits for each stage. Each sensor
can be individually optimized. For example, a button sensor
connected to STAGE0 can have different sensitivity and offset
values from those of a button with a different function that is
connected to a different stage.
CINx INPUT MULTIPLEXER SETUP
The CINx_CONNECTION_SETUP register bits provide options
for connecting the sensor input pins to the CDC (see Table 39
and Table 40).
The AD7148 has an on-chip multiplexer to route the input
signals from each pin to the input of the converter. Each input
pin can be tied to either the negative or the positive input of the
CDC, or it can be left floating. Each input can also be internally
connected to the BIAS signal to help prevent cross coupling. If
an input is not used, always connect it to BIAS.
Connecting a CINx input pin to the positive CDC input results
in an increase in CDC output code when the corresponding sensor
is activated. Connecting a CINx input pin to the negative CDC
input results in a decrease in CDC output code when the corre-
sponding sensor is activated.
The AD7148 performs a sequence of eight conversions. The
multiplexer can have different connection settings for each of
the eight conversions by using the CINx_CONNECTION_
SETUP bits. For example, CIN0 can be connected to the
negative CDC input or left floating. The same holds true for all
eight conversion stages.
Two bits in each sequence stage register control the mux setting for
the input pin, as shown in Figure 25.
SINGLE-ENDED CONNECTIONS TO THE CDC
A single-ended connection to the CDC is defined as having one
CINx input connected to either the positive or the negative CDC
input. A differential connection to the CDC is defined as having
one CINx input connected to the positive CDC input and a second
CINx input connected to the negative input of the CDC.
When a single-ended connection to the CDC is made in any
stage, the SE_CONNECTION_SETUP bits in the STAGEx_
CONNECTION_SETUP registers should be applied. These bits
ensure that, during a single-ended connection to the CDC, the
input paths to both terminals are matched. This matching of
input paths, in turn, improves the power supply rejection of the
converter measurement.
Table 11. Application of SE_CONNECTION_SETUP Bits
Bit Values
Description
00
Do not use.
01
Single-ended connection. For this stage, there is one
CINx connected to the positive CDC input.
10
Single-ended connection. For this stage, there is one
CINx connected to the negative CDC input.
11
Differential connection. For this stage, there is one
CINx connected to the negative CDC input and one
CINx connected to the positive CDC input.
If more than one CINx input is connected to either the positive
or negative input of the converter for the same conversion, set
SE_CONNECTION_SETUP = 11. For example, if CIN0 and
CIN3 are connected to the positive input of the CDC,
SE_CONNECTION_SETUP = 11.
CIN SETTING
CINx_CONNECTION
_SETUP BITS
00
CINx FLOATING
01
CINx CONNECTED TO
NEGATIVE CDC INPUT
10
CINx CONNECTED TO
POSITIVE CDC INPUT
11
CINx CONNECTED TO
BIAS
0
71
55
-0
24
CIN0
CIN1
CIN2
CIN3
CIN4
CIN5
CIN6
CIN7
+
CDC
–
Figure 25. Input Mux Configuration Options
相關PDF資料 |
PDF描述 |
|---|---|
| AD734BQ | IC MULTIPLIER 4-QUADRANT 14-CDIP |
| AD790SQ | IC COMPARATOR PREC W/LATCH 8CDIP |
| AD8013ANZ | IC OPAMP SINGLE 14DIP |
| AD8023ARZ | IC AMP VIDEO TRIPLE HC 14-SOIC |
| AD8073JNZ | IC VIDEO AMP TRIPLE 14-DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7150 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Ultra Low Power, 2 Channel, Capacitance Converter for Proximity Sensing |
| AD7150BRMZ | 功能描述:IC CAP CONV 2CH ULT LP 10MSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD7150BRMZ-REEL | 功能描述:IC CAP CONV 2CH ULT LP 10MSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD7151 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Ultra-Low Power, 1-Channel, Capacitance Converter for Proximity Sensing |
| AD7151BRMZ | 功能描述:IC CAP CONV 1CH ULT LP 10MSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。