參數資料
型號： AD7142ACPZ-500RL7
廠商： Analog Devices Inc
文件頁數： 22/73頁
文件大?。?/td> 0K
描述： IC CAP-TO-DGTL CONV PROG 32LFCSP
標準包裝： 1
類型： 電容數字轉換器
分辨率（位）： 16 b
采樣率（每秒）： 250k
數據接口： 串行
電壓電源： 單電源
電源電壓： 2.6 V ~ 3.6 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 32-VFQFN 裸露焊盤，CSP
供應商設備封裝： 32-LFCSP-VQ（5x5）
包裝： 標準包裝
其它名稱： AD7142ACPZ-500RL7DKR
AD7142
Rev. A | Page 28 of 72
GPIO INT OUTPUT CONTROL
The INT output signal can be controlled by the GPIO pin when
the GPIO is configured as an input. The GPIO is configured as
an input by setting the GPIO_SETUP bits in the interrupt
configuration register to 01. See the GPIO section for more
information on how to configure the GPIO.
Enable the GPIO interrupt by setting the GPIO_INT_EN bit in
Register 0x007 to 1, or disable the GPIO interrupt by clearing this
bit to 0. The GPIO status bit in the conversion complete interrupt
status register reflects the status of the GPIO interrupt. This bit is
set to 1 when the GPIO has triggered INT. The bit is cleared on
readback from the register, provided the condition that caused
the interrupt has gone away.
The GPIO interrupt can be set to trigger on a rising edge, falling
edge, high level, or low level at the GPIO input pin. Table 14
shows how the settings of the GPIO_INPUT_CONFIG bits in
the interrupt enable register affect the behavior of INT.
Figure 41 to Figure 44 show how the interrupt output is cleared on
a read from the CDC conversion complete interrupt status register.
GPIO
INPUT
INT
OUTPUT
SERIAL
READBACK
GPIO
INPUT
INT
OUTPUT
1
NOTES
1. READ GPIO_STATUS REGISTER TO RESET INT OUTPUT.
GPIO INPUT HIGH WHEN REGISTER IS READ BACK
GPIO INPUT LOW WHEN REGISTER IS READ BACK
05
70
2-
02
8
Figure 41. INT Output Controlled by the GPIO Input Example,
GPIO_SETUP = 01, GPIO_INPUT_CONFIG = 00
GPIO
INPUT
INT
OUTPUT
SERIAL
READBACK
GPIO
INPUT
INT
OUTPUT
1
GPIO INPUT HIGH WHEN REGISTER IS READ BACK
GPIO INPUT LOW WHEN REGISTER IS READ BACK
NOTES
1. READ GPIO_STATUS REGISTER TO RESET INT OUTPUT.
05
70
2-
0
29
Figure 42. INT Output Controlled by the GPIO Input Example,
GPIO_SETUP = 01, GPIO_INPUT_CONFIG = 01
相關PDF資料
PDF描述
AD7143ACPZ-1REEL IC CONV CAP-TO-DGTL PROG 16LFCSP
AD7147A-1ACBZ500R7 IC CDC 13CH I2C W/RAM 25WLCSP
AD7147WPACPZ-1500R IC CAP-TO-DGTL CONV PROG 24LFCSP
AD7150BRMZ-REEL IC CAP CONV 2CH ULT LP 10MSOP
AD7151BRMZ-REEL IC CAP CONV 1CH ULT LP 10MSOP
相關代理商/技術參數
參數描述
AD7142ACPZ-500RL71 制造商:AD 制造商全稱:Analog Devices 功能描述:Programmable Controller for Capacitance Touch Sensors
AD7142ACPZ-REEL 功能描述:IC CAP-TO-DGTL CONV PROG 32LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤
AD7142ACPZ-REEL1 制造商:AD 制造商全稱:Analog Devices 功能描述:Programmable Controller for Capacitance Touch Sensors
AD7143 制造商:AD 制造商全稱:Analog Devices 功能描述:Programmable Controller for Capacitance Touch Sensors
AD7143ACPZ 制造商:Analog Devices 功能描述:IC CDC 16BIT SMD LFCSP-16 7143 制造商:Analog Devices 功能描述:IC, CDC, 16BIT, SMD, LFCSP-16, 7143
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*