- 您現在的位置：買賣IC網 > PDF目錄36339 > 935264530157 (NXP SEMICONDUCTORS) SPECIALTY CONSUMER CIRCUIT, PQFP100 PDF資料下載
參數資料
| 型號： | 935264530157 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP100 |
| 封裝： | SOT-317, MQFP-100 |
| 文件頁數： | 13/43頁 |
| 文件大?。?/td> | 254K |
| 代理商： | 935264530157 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
1999 March 01
20
Philips Semiconductors
Product specication
Single chip DVB-C channel receiver
VES1820X
DESCRIPTION OF INTERNAL REGISTERS
1. CONF
0016 READ/WRITE
CLB
The CLB signal clears the VES1820X through the I2C interface (soft reset). To
clear the VES1820X, first write CLB = 0 followed by CLB = 1. This soft reset will
not affect the internal I2C registers contents.
TRI
When TRI is set to "1", all VES1820X outputs are tristated.
When TRI = 0 (default value) all outputs are active.
QAM[2:0]
QAM[2:0] indicates the modulation type according to the following table :
QAM[2:0]
Modulation
000
16-QAM
001
32-QAM
010
64-QAM (default)
011
128-QAM (DVB)
100
256-QAM
111
128-QAM (new
mapping)
INVIQ
When INVIQ=1, I and Q internal base-band signals are swapped to match a
spectral inversion. The default is INVIQ=0, no swap.
IFS
IFS determines if the input signal, FI[8:0] is interpreted in offset binary (IFS = 0,
default) or in 2’s complement (IFS = 1). It must be set to 1 when internal ADC is
used.
STDBY
When STDBY is set to "1" the VES1820X enters a StanD-BY mode and its power
consumption is reduced to TBD. The default value is STDBY = "0" which means
that the VES1820X is active.
2. AGCREF
0116 READ/WRITE
AGCR[7:0]
AGC Reference parameter.
AGCR[7:0] allows to adjust the analog signal level at the input of the VES1820X.
Depending on the modulation type, AGCR[7:0] must be set as follows (decimal
values) :
AGCR[7:0]
Modulation
140
16-QAM
140
32-QAM
106
64-QAM (default)
120
128-QAM
92
256-QAM
3. AGCONF
02
16
READ/WRITE
KAGC
KAGC[1:0] represents the AGC time constant. Default is KAGC[1:0] = 00.
The AGC loop bandwidth can be calculated with the following formula :
相關PDF資料 |
PDF描述 |
|---|---|
| 935264533557 | SPECIALTY CONSUMER CIRCUIT, PQFP100 |
| 935264539557 | SPECIALTY CONSUMER CIRCUIT, PQFP100 |
| 935266871557 | SPECIALTY CONSUMER CIRCUIT, PBGA292 |
| 935266917557 | SPECIALTY CONSUMER CIRCUIT, PBGA292 |
| 935268386557 | SPECIALTY CONSUMER CIRCUIT, PBGA292 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 935267356112 | 制造商:NXP Semiconductors 功能描述:IC TEA1507PN |
| 935268081112 | 制造商:NXP Semiconductors 功能描述:SUB ONLY IC |
| 935268721125 | 制造商:NXP Semiconductors 功能描述:Buffer/Line Driver 1-CH Non-Inverting 3-ST CMOS 5-Pin TSSOP T/R |
| 935269304128 | 制造商:ST-Ericsson 功能描述:IC AUDIO CODEC W/TCH SCRN 48LQFP |
| 935269544557 | 制造商:NXP Semiconductors 功能描述:SUB ONLY TDA9587-2US1-V1.3 |
發布緊急采購，3分鐘左右您將得到回復。