- 您現在的位置：買賣IC網 > PDF目錄24800 > 935260577557 (NXP SEMICONDUCTORS) TELECOM, CORDLESS, BASEBAND CIRCUIT, PQFP100 PDF資料下載
參數資料
| 型號： | 935260577557 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 無繩電話/電話 |
| 英文描述： | TELECOM, CORDLESS, BASEBAND CIRCUIT, PQFP100 |
| 封裝： | PLASTIC, SOT-407, LQFP-100 |
| 文件頁數： | 59/59頁 |
| 文件大?。?/td> | 781K |
| 代理商： | 935260577557 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁當前第59頁
1999 Jun 04
9
Philips Semiconductors
Product specication
Global Positioning System (GPS)
baseband processor
SAA1575HL
VCC(R)
72
Backup core power supply: 2.4 to 3.6 V only. Separate from the core supply to allow
a low capacity battery to be used to maintain the Real-Time Clock (RTC) function.
This should be powered from the main supply during normal operation and switched
to battery backup when the main supply fails.
DMCS
73
O
External data memory select: external RAM select pin, active LOW when the
external data memory space is addressed. This output is driven from VCC(R) and
VCC(B) supplies to ensure that the external RAM is not enabled during power-down.
PWRFAIL
74
I
Power fail indicator: a LOW on this pin forces the embedded microcontroller into
reset. Reset will not be de-asserted until a set time after both PWRDN and PWRFAIL
go HIGH. For correct start-up, this pin should be LOW on power-up.
XTAL4
75
O
Crystal 4: output from the RTC oscillator amplier; this pin is only 3 V tolerant
XTAL3
76
I
Crystal 3: input to inverting amplier used in the RTC oscillator circuits (32.768 kHz);
this pin is only 3 V tolerant
PWRB
77
O
Backup supply select: this output is intended to drive an external FET used to switch
the battery backup supply(s). It is active LOW and is controlled directly by the
PWRFAIL.
PWRM
78
O
Main supply select: this output is intended to drive an external FET used to switch
the main supply(s). It is active LOW and is controlled directly by PWRFAIL.
VSS
79
Ground: 0 V reference
VCC(B)
80
Backup I/O power supply: 2.4 to 5.5 V only. Supply for the RAM select, power fail
and power switching I/O pads only allowing these functions to be powered when the
main power supply fails. This should be powered from the main supply during normal
operation and switched to battery backup when the main supply fails.
TXD1
81
O
Transmitter output 1: transmit channel for serial port 1 (UART1) of the embedded
processor
RXD1
82
I
Receiver input 1: receive channel for serial port 1 (UART1) of the embedded
processor. It is intended that this serial port is dedicated to differential GPS
information (dependent on rmware).
TXD0
83
O
processor.
RXD0
84
I
Receiver input 0: receive channel for serial port 0 (UART0) of the embedded
processor. It is intended that this serial port is dedicated to the NMEA data stream
(dependent on rmware).
VSS
85
Ground: 0 V reference
VCC(P)
86
Main I/O power supply: 2.7 to 5.5 V operating range; main supply for the periphery
in normal operation
GPIO4
87
I/O
GPIO bit 4: standard general purpose I/O mapped into the segment 15 of the address
space. The top 4 bits can be used as the XA external timer control access pins
(T0, T1, T2 and T2EX).
GPIO3
88
I/O
GPIO bit 3: standard general purpose I/O mapped into the segment 15 of the address
space. The top 4 bits can be used as the XA external timer control access pins
(T0, T1, T2 and T2EX).
RFDAT
89
O
RFIC set-up data: serial data output used to set up the UAA1570HL front-end IC.
RFCLK
90
O
RFIC set-up data: clock output for the serial data output used to set up the
UAA1570HL front-end IC. The state of the RFDAT and RFLE lines is latched into the
front-end IC on the rising edge.
SYMBOL
PIN
I/O
DESCRIPTION
相關PDF資料 |
PDF描述 |
|---|---|
| 935260580118 | LOW SKEW CLOCK DRIVER, 18 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO48 |
| 935260608112 | TELEPHONE MULTIFUNCTION CKT, PDSO28 |
| 935260608118 | TELEPHONE MULTIFUNCTION CKT, PDSO28 |
| 935260687112 | TELEPHONE MULTIFUNCTION CKT, PDSO28 |
| 935260687118 | TELEPHONE MULTIFUNCTION CKT, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 935261069122 | 制造商:NXP Semiconductors 功能描述:IC SECURITY TRANSPONDER PLLMC |
| 935262025112 | 制造商:NXP Semiconductors 功能描述:SUB ONLY IC |
| 935262217118 | 制造商:NXP Semiconductors 功能描述:Real Time Clock Serial 8-Pin SO T/R |
| 935264217557 | 制造商:NXP Semiconductors 功能描述:SUB ONLY IC |
| 935267356112 | 制造商:NXP Semiconductors 功能描述:IC TEA1507PN |
發布緊急采購，3分鐘左右您將得到回復。