- 您現在的位置：買賣IC網 > PDF目錄358656 > 89C61X2 (NXP Semiconductors N.V.) 80C51 8-bit Flash microcontroller family PDF資料下載
參數資料
| 型號： | 89C61X2 |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 8位微控制器 |
| 英文描述： | 80C51 8-bit Flash microcontroller family |
| 中文描述： | 80C51的8位閃存微控制器系列 |
| 文件頁數： | 19/56頁 |
| 文件大?。?/td> | 342K |
| 代理商： | 89C61X2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
Philips Semiconductors
Product data
P89C60X2/61X2
80C51 8-bit Flash microcontroller family
64KB Flash, 512B/1024B RAM
2003 Sep 11
19
OSCILLATOR CHARACTERISTICS
Using the oscillator, XTAL1 and XTAL2 are the input and output,
respectively, of an inverting amplifier. The pins can be configured for
use as an on-chip oscillator, as shown in the logic symbol.
To drive the device from an external clock source, XTAL1 should be
driven while XTAL2 is left unconnected. However, minimum and
maximum high and low times specified in the data sheet must be
observed.
Clock Control Register (CKCON)
This device provides control of the 6-clock/12-clock mode by both
an SFR bit (bit X2 in register CKCON) and a Flash bit (bit FX2,
located in the Security Block). When X2 is 0, 12-clock mode is
activated. By setting this bit to 1, the system is switching to 6-clock
mode. Having this option implemented as SFR bit, it can be
accessed anytime and changed to either value. Changing X2 from 0
to 1 will result in executing user code at twice the speed, since all
system time intervals will be divided by 2. Changing back from
6-clock to 12-clock mode will slow down running code by a factor of
2.
The Flash clock control bit (FX2) activates the 6-clock mode when
programmed using a parallel programmer, superceding the X2 bit
(CKCON.0). Please also see Table 4 below.
Table 4.
FX2 clock mode bit
(can only be set by
parallel programmer)
X2 bit
(CKCON.0)
CPU clock mode
erased
0
12-clock mode
(default)
erased
1
6-clock mode
programmed
X
6-clock mode
Programmable Clock-Out Pin
A 50% duty cycle clock can be programmed to be output on P1.0.
This pin, besides being a regular I/O pin, has two alternate
functions. It can be programmed:
1. to input the external clock for Timer/Counter 2, or
2. to output a 50% duty cycle clock ranging from 61 Hz to 4 MHz at
a 16 MHz operating frequency in 12-clock mode (122 Hz to
8 MHz in 6-clock mode).
To configure the Timer/Counter 2 as a clock generator, bit C/T2 (in
T2CON) must be cleared and bit T20E in T2MOD must be set. Bit
TR2 (T2CON.2) also must be set to start the timer.
The Clock-Out frequency depends on the oscillator frequency and
the reload value of Timer 2 capture registers (RCAP2H, RCAP2L)
as shown in this equation:
Oscillator Frequency
(65536–RCAP2H,RCAP2L)
n
Where:
n = 2 in 6-clock mode, 4 in 12-clock mode.
(RCAP2H,RCAP2L) = the content of RCAP2H and RCAP2L
taken as a 16-bit unsigned integer.
In the Clock-Out mode Timer 2 roll-overs will not generate an
interrupt. This is similar to when it is used as a baud-rate generator.
It is possible to use Timer 2 as a baud-rate generator and a clock
generator simultaneously. Note, however, that the baud-rate and the
Clock-Out frequency will be the same.
RESET
A reset is accomplished by holding the RST pin HIGH for at least
two machine cycles (24 oscillator periods in 12-clock and 12
oscillator periods in 6-clock mode), while the oscillator is running. To
insure a reliable power-up reset, the RST pin must be high long
enough to allow the oscillator time to start up (normally a few
milliseconds) plus two machine cycles, unless it has been set to
6-clock operation using a parallel programmer.
LOW POWER MODES
Stop Clock Mode
The static design enables the clock speed to be reduced down to
0 MHz (stopped). When the oscillator is stopped, the RAM and
Special Function Registers retain their values. This mode allows
step-by-step utilization and permits reduced system power
consumption by lowering the clock frequency down to any value. For
lowest power consumption the Power Down mode is suggested.
Idle Mode
In idle mode (see Table 5), the CPU puts itself to sleep while all of
the on-chip peripherals stay active. The instruction to invoke the idle
mode is the last instruction executed in the normal operating mode
before the idle mode is activated. The CPU contents, the on-chip
RAM, and all of the special function registers remain intact during
this mode. The idle mode can be terminated either by any enabled
interrupt (at which time the process is picked up at the interrupt
service routine and continued), or by a hardware reset which starts
the processor in the same manner as a power-on reset.
相關PDF資料 |
PDF描述 |
|---|---|
| 8AGP1 | Fast Blow Fuse Series |
| 8T34HA | Thyristor Product Catalog |
| 90-030A | Industrial Control IC |
| 90-030G | Industrial Control IC |
| 90-030S | Industrial Control IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 89C664HFA | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 89-CBSAP-2.5X3.5X0.8 | 功能描述:89-CBSAP-2.5X3.5X0.8--89S14--CIR 制造商:leader tech inc. 系列:* 零件狀態:在售 類型:屏蔽，分體式 高度 - 總:0.800"（20.32mm） 長度 - 總:3.500"（88.90mm） 寬度 - 總:2.500"（63.50mm） 通風:通風孔，按樣式排列 安裝類型:通孔 標準包裝:5 |
| 89-CBSFND-2.25X3.75X0.80 | 功能描述:89-CBSFND-2.25X3.75X0.80--89S35- 制造商:leader tech inc. 系列:* 零件狀態:在售 類型:屏蔽，分體式 高度 - 總:0.800"（20.32mm） 長度 - 總:3.750"（95.25mm） 寬度 - 總:2.250"（57.15mm） 通風:通風孔，按樣式排列 安裝類型:通孔 標準包裝:20 |
| 89-CBSFNSV-2.0X7.0X0.8 | 功能描述:89-CBSFNSV-2.0X7.0X0.8--89S36--C 制造商:leader tech inc. 系列:* 零件狀態:在售 類型:屏蔽，分體式 高度 - 總:0.800"（20.32mm） 長度 - 總:7.000"（177.80mm） 寬度 - 總:2.000"（50.80mm） 通風:通風孔，按樣式排列 安裝類型:通孔 標準包裝:20 |
| 89-CBSU-24" | 功能描述:89-CBSU-24"--89S01--FLAT FENCE S 制造商:leader tech inc. 系列:* 零件狀態:在售 類型:屏蔽，分體式 長度 - 總:- 通風:通風孔，按樣式排列 安裝類型:通孔 標準包裝:5 |
發布緊急采購，3分鐘左右您將得到回復。