- 您現在的位置：買賣IC網 > PDF目錄369230 > 68HC705BD7 (Motorola, Inc.) 8-Bit Microcontroller Units (MCU).(8位微控制器) PDF資料下載
參數資料
| 型號： | 68HC705BD7 |
| 廠商： | Motorola, Inc. |
| 英文描述： | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 中文描述： | 8位微控制器單元（MCU）。（8位微控制器） |
| 文件頁數： | 53/85頁 |
| 文件大小： | 302K |
| 代理商： | 68HC705BD7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁當前第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁
SECTION 9: DDC12AB INTERFACE
MOTOROLA
Page 43
MC68HC05BD7 Rev. 2.0
GENERAL RELEASE SPECIFICATION
PRELMNARY
Bit 3
If the received acknowledge bit (RXAK) is low, it indicates an
acknowledge signal has been received after the completion of
8 data bits transmission on the bus. If RXAK is high, it
indicates no acknowledge signal has been detected at the 9th
clock. Then the module will release the SDA line for the
master to generate ’stop’ or ’repeated start’ condition. It is set
upon reset.
Bit 2
This SCLIF flag is set by the falling edge of SCL line only
when DDC1EN is enabled. This bit is cleared by writing zero
to it, clearing DDC1EN bit or when the DEN is disable.
9.3.4
DDC Status Register (DSR)
This status register is readable only. All bits are cleared upon reset except bit 3 (RXAK) and
bit 1 (TXBE).
RXIF
Bit 7
is loaded with a newly received data. Once the DDRR is
loaded with received data, no more received data can be
loaded to the DDRR register. The only way to release the
DDRR register for loading next received data is that software
reads the data from the DDRR register to clear RXBF flag.
This bit is cleared by writing ’0’ to it or when the DEN is
disabled.
The data Transmit Interrupt Flag is set before the data of the
DDTR register is downloaded to the shift register. It is
software’s responsibility to fill the DDTR register with new
data when this bit is set. This bit is cleared by writing ’0’ to it
or when the DEN is disabled.
The MATCH flag is set when the received data in the DDRR
register is an calling address which matches with the address
or its extended addresses (EXTAD=1) specified in the DADR
register.
The Slave RW bit will indicate the data direction of DDC
protocol. It is updated after the calling address is received in
the DDC2 protocol. When it is one, the master will read the
data from DDC module, so the module is in transmit mode.
When it is zero, the master will send data to the DDC module,
the module is in receive mode. When DDC1EN is set, the
TXIF
Bit 6
MATCH
Bit 5
SRW
Bit 4
RXAK
SCLIF
0
7
TXBE
0
0
0
1
0
1
0
6
5
4
3
2
1
0
RXBF
W
R
DSR
$0019
reset
SCLIF
MATCH
RXAK
SRW
TXIF
RXIF
相關PDF資料 |
PDF描述 |
|---|---|
| 68HC05J5A | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 68HC705J5A | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 68HRC05J5A | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 68HRC705J5A | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 68HC05K0 | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 68HC705C5 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:SPECIFICATION(General Release) |
| 68HC705C8 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:PROGRAMMING REFRERENCE GUIDE |
| 68HC705C8ACP | 制造商: 功能描述: 制造商:Motorola Inc 功能描述: 制造商:undefined 功能描述: |
| 68HC705CJ4FB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| 68HC705CJ4P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。