- 您現在的位置：買賣IC網 > PDF目錄369230 > 68HC705BD7 (Motorola, Inc.) 8-Bit Microcontroller Units (MCU).(8位微控制器) PDF資料下載
參數資料
| 型號： | 68HC705BD7 |
| 廠商： | Motorola, Inc. |
| 英文描述： | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 中文描述： | 8位微控制器單元（MCU）。（8位微控制器） |
| 文件頁數： | 44/85頁 |
| 文件大?。?/td> | 302K |
| 代理商： | 68HC705BD7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁當前第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁
MOTOROLA
Page 34
SECTION 7: INPUT/OUTPUT PORTS
GENERAL RELEASE SPECIFICATION
MC68HC05BD7 Rev. 2.0
Figure 7-1: Port I/O Circuitry
shares its pin with the CLAMP output. See
SECTION 10
for the description of CLAMP
signal. It becomes the CLAMP output when the CLAMP bit in SPIOCR register is set. PD3
is a +12V open-drain I/O pin which shares its pin with the SOG input. Also see
SECTION
10
for the description of SOG input. It is configured as SOG input when the SOG bit in
SPIOCR register is set. The Port D data register is at $03 and the data direction register
(DDR) is at $07. Reset does not affect the data register, yet clears the data direction
register, thereby returning the ports to inputs. Writing a one to a DDR bit sets the
corresponding port bit to output mode.
7.5
Input/Output Programming
Bidirectional port lines may be programmed as an input or an output under software control.
The direction of the pins is determined by the state of the corresponding bit in the port data
direction register (DDR). Each port has an associated DDR. Any I/O port pin is configured
as an output if its corresponding DDR bit is set. A pin is configured as an input if its
corresponding DDR bit is cleared.
During Reset, all DDRs are cleared, which configure all port pins as inputs. The data
direction registers are capable of being written to or read by the processor. During the
programmed output state, a read of the data register actually reads the value of the output
data latch and not the I/O pin. See
Figure 7-1
and .
I/O
PIN
Read Data
Write Data
Data
Register Bit
Internal HC05
Data Bus
Reset
(RST)
Read/Write DDR
Data Direction
Register Bit
OUTPUT
相關PDF資料 |
PDF描述 |
|---|---|
| 68HC05J5A | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 68HC705J5A | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 68HRC05J5A | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 68HRC705J5A | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 68HC05K0 | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 68HC705C5 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:SPECIFICATION(General Release) |
| 68HC705C8 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:PROGRAMMING REFRERENCE GUIDE |
| 68HC705C8ACP | 制造商: 功能描述: 制造商:Motorola Inc 功能描述: 制造商:undefined 功能描述: |
| 68HC705CJ4FB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| 68HC705CJ4P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。