參數資料
| 型號： | XRT83L38IB |
| 廠商： | Exar Corporation |
| 文件頁數： | 68/87頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU T1/E1/J1 OCTAL 225BGA |
| 標準包裝： | 84 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 8/8 |
| 規程： | T1，E1，J1 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 225-BGA |
| 供應商設備封裝： | 225-BGA（19x19） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁當前第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁
XRT83L38
67
OCTAL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
REV. 1.0.2
CLOCK SELECT REGISTER
The input clock source is used to generate all the necessary clock references internally to the LIU. The
microprocessor timing is derived from a PLL output which is chosen by programming the Clock Select Bits and
the Master Clock Rate in register 0x81h. Therefore, if the clock selection bits or the MCLRATE bit are being
programmed, the frequency of the PLL output will be adjusted accordingly.
During this adjustment, it is
important to "Not" write to any other bit location within the same register while selecting the input/output clock
frequency. For best results, register 0x81h can be broken down into two sub-registers with the MSB being bits
D[7:3] and the LSB being bits D[2:0] as shown in Figure 25. Note: Bit D[7] is a reserved bit.
FIGURE 25. REGISTER 0X81H SUB REGISTERS
Programming Examples:
Example 1: Changing bits D[7:3]
If bits D[7:3] are the only values within the register that will change in a WRITE process, the microprocessor
only needs to initiate ONE write operation.
Example 2: Changing bits D[2:0]
If bits D[2:0] are the only values within the register that will change in a WRITE process, the microprocessor
only needs to initiate ONE write operation.
Example 3: Changing bits within the MSB and LSB
In this scenario, one must initiate TWO write operations such that the MSB and LSB do not change within ONE
write cycle. It is recommended that the MSB and LSB be treated as two independent sub-registers. One can
either change the clock selection (MSB) and then change bits D[2:0] (LSB) on the SECOND write, or vice-
versa. No order or sequence is necessary.
TABLE 36: MICROPROCESSOR REGISTER #129, BIT DESCRIPTION
REGISTER ADDRESS
10000001
NAME
FUNCTION
REGISTER
TYPE
RESET
VALUE
BIT #
D7
Reserved
R/W
0
D0
D1
D2
D3
D4
D5
D6
D7
MSB
LSB
Clock Selection Bits
ExLOS, ICT
相關PDF資料 |
PDF描述 |
|---|---|
| IDT72V3660L10PF8 | IC FIFO SS 4096X36 10NS 128-TQFP |
| MS3101F20-23PW | CONN RCPT 2POS FREE HNG W/PINS |
| XRT75R03DIV | IC LIU E3/DS3/STS-1 3CH 128LQFP |
| ISL26710IHZ-T | IC ADC 10BIT SPI/SRL 1M 8-SOT-23 |
| MS27472T10F35SB | CONN RCPT 13POS WALL MNT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT83L38IB-F | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT83L38IV | 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83SH314 | 制造商:EXAR 制造商全稱:EXAR 功能描述:14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83SH314_0610 | 制造商:EXAR 制造商全稱:EXAR 功能描述:14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83SH314ES | 功能描述:外圍驅動器與原件 - PCI 14 CHT1/E1LIU SH RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。