參數資料
型號： XRT83L34IVTR-F
廠商： Exar Corporation
文件頁數： 57/99頁
文件大小： 0K
描述： IC LIU T1/E1/J1 QUAD 128TQFP
標準包裝： 750
類型： 線路接口裝置（LIU）
驅動器/接收器數： 4/4
規程： T1，E1，J1
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 128-LQFP
供應商設備封裝： 128-TQFP（14x20）
包裝： 帶卷 (TR)
XRT83L34
xr
REV. 1.0.1
QUAD T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
57
CONFIGURING
THE
MICROPROCESSOR
INTERFACE
TO
OPERATE
IN
THE
MOTOROLA-
ASYNCHRONOUS MODE
The user can configure the Microprocessor Interface to operate in the Motorola-Asynchronous Mode by tying
the UPTS1 (Pin 106) to the logic "HIGH" level.
Finally, if the Microprocessor Interface has been configured to operate in the Motorola-Asynchronous Mode,
then it will perform READ and WRITE operations as described below.
THE MOTOROLA-ASYNCHRONOUS READ-CYCLE:
If the Microprocessor Interface (of the XRT83L34 device) has been configured to operate in the Motorola-
Asynchronous Mode, then the Microprocessor Interface should do all of the following, anytime it wishes to read
out the contents of a register within the XRT83L34 device.
1. Place the address of the "target" register within the XRT83L34 device, on the Address Bus Input pins,
A[6:0].
2. While the Microprocessor is placing the address value on the Address Bus, the Address Decoding circuitry
(within the user’s system) should assert the CS* (Chip Select input) pin of the XRT83L34 device, by tog-
gling it "LOW". This action enables further communication between the MIcroprocessor and the XRT83L34
Microprocessor Interface block.
3. Assert the ALE/AS (Address Strobe) input pin by toggling it "LOW". This step enables the Address Bus
input drivers, within the Microprocessor Interface block of the XRT83L34 device.
4. Afterwards, the Microprocessor should indicate that this cycle is a "READ" cycle by setting the WR*/R/W*
(R/W*) input pin "HIGH".
5. Next, the Microprocessor should initiate the current bus cycle by toggling the RD*/DS* (Data Strobe) input
pin "LOW". This step enables the bi-directional data bus output drivers, within the XRT83L34 device. At
this point, the bi-directional data bus output drivers will proceed to drive the contents of the "Addressed"
register onto the bi-directional data bus, D[7:0].
6. Immediately after the Microprocessor toggles the "Data Strobe" (RD*/DS*) signal "LOW", the XRT83L34
device will continue to drive the RDY*/DTACK* output pin "HIGH". The XRT83L34 device does this in order
to inform the Microprocessor that the data (to be read from the data bus) is "NOT READY" to be latched
into the Microprocessor. In this case, the Microprocessor should continue to hold the "Data Strobe" (RD*/
DS*) signal "LOW" until it detects the "RDY*/DTACK*" output pin toggling "LOW".
7. After some settling time, the data on the "Bi-Directional" Data Bus will stabilize and can be read by the
Microprocessor. The XRT83L34 device will indicate that this data can be read by asserting the RDY*/
DTACK* (DTACK) output signal (by toggling it "LOW").
8. After the Microprocessor detects the RDY*/DTACK* signal (from the XRT83L34 device) toggling "LOW", it
can now terminate the Ready Cycle by toggling the "RD*/DS*" (Data Strobe) input pin "HIGH".
Figure _ presents a timing diagram that illustrates the behavior of the Microprocessor Interface signals during a "Motorola-
相關PDF資料
PDF描述
XRT83L34IVTR IC LIU T1/E1/J1 QUAD 128TQFP
VI-B6H-MX-B1 CONVERTER MOD DC/DC 52V 75W
IDT72V841L15PFI8 IC FIFO SYNC 2048X18 15NS 64QFP
VI-22V-MY CONVERTER MOD DC/DC 5.8V 50W
MS3106R28-15S CONN PLUG 35POS STRAIGHT W/SCKT
相關代理商/技術參數
參數描述
XRT83L38 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XRT83L38_07 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XRT83L38ES 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT83L38ES-BG 功能描述:界面開發工具 Eval System for XRT83L38 Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XRT83L38IB 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*