- 您現在的位置：買賣IC網 > PDF目錄1976 > XR20V2172IL64-F (Exar Corporation)IC UART/TXRX I2C/SPI RS232 64QFN PDF資料下載
參數資料
| 型號： | XR20V2172IL64-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 28/51頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART/TXRX I2C/SPI RS232 64QFN |
| 標準包裝： | 260 |
| 特點： | * |
| 通道數： | 2，DUART |
| FIFO's： | 64 字節 |
| 規程： | RS232 |
| 電源電壓： | 2.97 V ~ 3.63 V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 64-QFN（9x9） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
XR20V2172
34
TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO AND RS232 TRANSCEIVER
REV. 1.0.2
4.16
GPIO State Register (IOState) = Read/Write
This register reports the state of all GPIO pins during a read and writes to any GPIO that is an output.
Logic 0 = set output pin LOW
Logic 1 = set output pin HIGH
4.17
GPIO Interrupt Enable Register (IOIntEna) - Read/Write
This register enables the interrupt for the GPIO pins. The interrupts for GPIO[7:4] are only enabled if
IOControl[1] = 0. If IOControl[0] = 1 (GPIO pins are selected as modem IOs) , then IOIntEna[7:4] will have no
effect on GPIO[7:4].
Logic 0 = a change in the input pin will not generate an interrupt
Logic 1 = a change in the input will generate an interrupt
4.18
GPIO Control Register (IOControl) - Read/Write
IOControl bits 2-1 should be set to a logic 1 to behave like modem IOs that can be controlled and monitored via
the MCR and MSR registers. If not, by default, they are GPIOs controlled by IODir, IOState and IOIntEna.
IOControl[7:4]: Reserved
IOControl[3]: UART Software Reset
Writing a logic 1 to this bit will reset the device. Once the device is reset, this bit will automatically be set to a
logic 0.
IOControl[2]: GPIO[3:0] or Modem IO Select (CH B)
This bit controls whether GPIO[3:0] behave as GPIO pins or as modem IO pins (RIB#, CDB#, DTRB#, DSRB#)
Logic 0 = GPIO[3:0] behave as GPIO pins
Logic 1 = GPIO[3:0] behave as RIB#, CDB#, DTRB#, DSRB#. Note: DTRB# will also need to be set as an
output via IODir bit-1.
IOControl[1]: GPIO[7:4] or Modem IO Select (CH A)
This bit controls whether GPIO[7:4] behave as GPIO pins or as modem IO pins (RIA#, CDA#, DTRA#, DSRA#)
Logic 0 = GPIO[7:4] behave as GPIO pins
Logic 1 = GPIO[7:4] behave as RIA#, CDA#, DTRA#, DSRA#. Note: DTRA# will also need to be set as an
output via IODir bit-5.
IOControl[0]: IO Latch
This bit enable/disable GPIO inputs latching.
Logic 0 = GPIO input values are not latched. A change in any GPIO input generates an interrupt. A read of
the IOState register clears the interrupt. If the input goes back to its initial logic state before the input register
is read, then the interrupt is cleared.
Logic 1 = GPIO input values are latched. A change in the GPIO input generates an interrupt and the input
logic value is loaded in the bit of the corresponding input state register (IOState). A read of the IOState
register clears the interrupt. If the input pin goes back to its initial logic state before the interrupt register is
read, then the interrupt is not cleared and the corresponding bit of the IOState register keeps the logic value
that generated the interrupt.
相關PDF資料 |
PDF描述 |
|---|---|
| XR21V1410IL16TR-F | IC USB UART FIFO FULL SPD 16QFN |
| XR21V1412IL32TR-F | IC USB UART FIFO FULL SPD 32QFN |
| XR21V1414IM48-F | IC UART FIFO USB QUAD 48TQFP |
| XR3178EID-F | IC TXRX RS485 DIFF 3V 8NSOIC |
| XR5488EID-F | IC TXRX RS485 PROFIBUS 8NSOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR20V2172L64-0A-EB | 功能描述:UART 接口集成電路 Supports V2172 64pin QFN, I2C Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR20V2172L64-0B-EB | 功能描述:UART 接口集成電路 Supports V2172 64pin QFN, SPI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR-210 | 制造商:EXAR 制造商全稱:EXAR 功能描述:FSK MODULATOR / DEMODULATOR |
| XR-2100CJ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MODEM |
| XR-2100CP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MODEM |
發布緊急采購，3分鐘左右您將得到回復。