- 您現在的位置：買賣IC網 > PDF目錄376454 > XR16L788IQ (EXAR CORP) HIGH PERFORMANCE OCTAL UART PDF資料下載
參數資料
| 型號： | XR16L788IQ |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | HIGH PERFORMANCE OCTAL UART |
| 中文描述： | 8 CHANNEL(S), 6.25M bps, SERIAL COMM CONTROLLER, PQFP100 |
| 封裝： | 14 X 20 MM, 3 MM HEIGHT, PLASTIC, QFP-100 |
| 文件頁數： | 27/42頁 |
| 文件大?。?/td> | 557K |
| 代理商： | XR16L788IQ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
XR16L788 OCTAL UART
á
REV. 1.1.4
27
MCR[4]: Internal Loopback Enable
Logic 0 = Disable loopback mode. (default)
Logic 1 = Enable local loopback mode, see loop-
back section and
Figure 10
.
MCR[5]: Xon-Any Enable
Logic 0 = Disable Xon-Any function (for 16C550
compatibility). (default).
Logic 1 = Enable Xon-Any function. In this mode
any RX character received will enable Xon, resume
data transmission.
MCR[6]: Infrared Encoder/Decoder Enable
The state of this bit depends on the sampled logic
level of pin ENIR during power up, following a hard-
ware reset or a soft-reset. Afterward user can over-
ride this bit for desired operation.
Logic 0 = Enable the standard modem receive and
transmit character interface.
Logic 1 = Enable infrared IrDA receive and transmit
inputs/outputs. While in this mode, the TX/RX out-
put/input are routed to the infrared encoder/
decoder. The data input and output levels will con-
form to the IrDA infrared interface requirement. As
such, while in this mode the infrared TX output will
be a logic 0 during idle data conditions. FCTR bit-4
may be selected to invert the RX input signal level
going to the decoder for infrared modules that pro-
vide rather an inverted output.
MCR[7]: Clock Prescaler Select
Logic 0 = Divide by one. The input clock from the
crystal or external clock is fed directly to the Pro-
grammable Baud Rate Generator without further
modification, i.e., divide by one. (default).
Logic 1 = Divide by four. The prescaler divides the
input clock from the crystal or external clock by four
and feeds it to the Programmable Baud Rate Gen-
erator, hence, data rates become one forth.
Line Status Register (LSR)
This register provides the status of data transfers be-
tween the UART and the host.
LSR[0]: Receive Data Ready Indicator
Logic 0 = No data in receive holding register or
FIFO. (default).
Logic 1 = Data has been received and is saved in
the receive holding register or FIFO.
LSR[1]: Receiver Overrun Flag
Logic 0 = No overrun error. (default)
Logic 1 = Overrun error. A data overrun error condi-
tion occurred in the receive shift register. This hap-
pens when additional data arrives while the FIFO is
full. In this case the previous data in the receive
shift register is overwritten. Note that under this
condition the data byte in the receive shift register
is not transferred into the FIFO, therefore the data
in the FIFO is not corrupted by the error.
LSR[2]: Receive Data Parity Error Flag
Logic 0 = No parity error. (default)
Logic 1 = Parity error. The receive character in
RHR does not have correct parity information and
is suspect. This error is associated with the charac-
ter available for reading in RHR.
LSR[3]: Receive Data Framing Error Flag
Logic 0 = No framing error. (default)
Logic 1 = Framing error. The receive character did
not have a valid stop bit(s). This error is associated
with the character available for reading in RHR.
LSR[4]: Receive Break Flag
Logic 0 = No break condition. (default)
Logic 1 = The receiver received a break signal (RX
was a logic 0 for one character frame time). In the
FIFO mode, only one break character is loaded into
the FIFO. The break indication remains until the RX
input returns to the idle condition, “mark” or logic 1.
LSR[5]: Transmit Holding Register Empty Flag
This bit is the Transmit Holding Register Empty indi-
cator. This bit indicates that the transmitter is ready to
accept a new character for transmission. In addition,
this bit causes the UART to issue an interrupt to the
host when the THR interrupt enable is set. The THR
bit is set to a logic 1 when the last data byte is trans-
ferred from the transmit holding register to the trans-
mit shift register. The bit is reset to logic 0 concurrent-
ly with the data loading to the transmit holding regis-
ter by the host. In the FIFO mode this bit is set when
the transmit FIFO is empty; it is cleared when at least
1 byte is written to the transmit FIFO.
LSR[6]: Transmit Shift Register Empty Flag
This bit is the Transmit Shift Register Empty indicator.
This bit is set to a logic 1 whenever the transmitter
goes idle. It is set to logic 0 whenever either the THR
or TSR contains a data character. In the FIFO mode
this bit is set to one whenever the transmit FIFO and
transmit shift register are both empty.
LSR[7]: Receive FIFO Data Error Flag
Logic 0 = No FIFO error. (default)
Logic 1 = An indicator for the sum of all error bits in
the RX FIFO. At least one parity error, framing error
or break indication is in the FIFO data. This bit
clears when there is no more error(s) in the FIFO.
相關PDF資料 |
PDF描述 |
|---|---|
| XR17C154 | Tip, Offset Tapered Needle, 1mm Diameter |
| XR17C154CV | Burner |
| XR17C154IV | Tools, Heatgun; Leaded Process Compatible:No; Peak Reflow Compatible (260 C):No RoHS Compliant: No |
| XR17C158 | PCI Bus Octal UART(八通用異步接收器/發送器（滿足通訊系統中PCI總線和高帶寬要求）) |
| XR17D152 | UNIVERSAL (3.3V AND 5V) PCI BUS DUAL UART |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16L788IQ-F | 功能描述:UART 接口集成電路 2.97V-5.5V 64B FIFO temp -45 to 85C RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16L788IQTR-F | 功能描述:UART 接口集成電路 3.3V OCTAL UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16M2550 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE LOW VOLTAGE DUART WITH 16-BYTE FIFO |
| XR16M2550IL-0B-EB | 功能描述:UART 接口集成電路 Supports M2550 32pin QFN, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16M2550IL32 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。