參數資料
型號： X80000Q32I
廠商： INTERSIL CORP
元件分類： 電源管理
英文描述： Smart Power Plug Penta-Power Sequence Controller with Hot Swap
中文描述： 5-CHANNEL POWER SUPPLY SUPPORT CKT, QCC32
封裝： 7 X 7 MM, 0.65 MM PITCH, QFN-32
文件頁數： 19/37頁
文件大?。?/td> 695K
代理商： X80000Q32I
19
FN8148.0
March 18, 2005
Overcurrent During Insertion
Insertion is defined as the first plug-in of the board to the
backplane. In this case, the X80000 is initially fully powered
off prior to the hot plug connection to the mains supply. This
condition is different from a situation where the mains supply
has temporarily failed resulting in a partial recycle of the
power. This second condition will be referred to as a power
cycle.
During insertion, the board can experience high levels of
current for short periods of time as power supply capacitors
charge up on the power bus. To prevent the overcurrent
sensor from turning off the FET inadvertently, the X80000
has the ability to allow more current to flow through the
powerFET and the sense resistor for a short period of time
until the FET turns on and the PWRGD signal goes active. In
the standard setting, 200mV is allowed across sense resistor
the during insertion (10A assuming a 20mW resistor). Two
bits in register CR4 select the insertion current limit of 1X,
2X, 3X or 4X the base setting of 50mV. This provides a
mechanism to reduce insertion issues associated with huge
current surges.
Hardshort Protection - Programmable Retry
In the event on an overcurrent or hard short condition, the
X80000 includes a retry circuit. This circuit waits for 100ms,
then attempts to again turn on the FET. If the fault condition
still exists, the FET turns off and a retry counter
(SC_Counter) increments. After the selected number of
failed trys, the X80000 sets a Failed After Retry Status
(FAR_STAT) fault bit, sets the FAR pin LOW and goes into
an idle state. In this state the GATE pin will not go active until
the device is cleared.
The retry circuit can be programmed to handle the retry
operation in one of eight ways (See Table 6). The options
allow retries from zero to unlimited and specifies when to
assert the FAR (Failure After Re-Try) signal. In the “Always
Retry” case there is no idle state, so when the overcurrent
condition clears, the GATE goes active and the FET turns
on.
There are four optional retry delay periods. These are
100ms, 500ms, 1s, and 5s. These are programmed by bits
located in the CR2 register.
After FAR is asserted, there are two ways to clear the
hardshort protection:
1. Master Reset Hot Side. The master reset pin, MRH, can
be asserted by pulling it LOW. Upon MRH assertion, all
default values are restored and the retry is cleared.
2. Power cycle the part, turning V
DD
OFF, then ON.
If an overcurrent condition does not occur on any retry, the
gate pin will proceed to open at the user defined slew rate.
Overcurrent Fault Condition Flags
On any overcurrent violation, the X80000 will cut-off the
GATE, turning off the voltage to the load, and setting all
power good pins to their disabled state. In this condition, the
fault-overcurrent bit (FOC) goes LOW. To clear FOC,
remove the over current condition, then write to the control
register. Refer to instructions on writing to the FDR (See
Table 8).
TABLE 5. INSERTION OVERCURRENT THRESHOLD OPTIONS
VS1
VS0
V
OCI
0
0
50mV (1X)
0
1
100mV (2X)
1
0
150mV (3X)
1
1
200mV (4X)
2 bit
noise
filtering
Control
Registers
SDA
SCL
Overcurrent
Logic and Gate
Control Block
Short-Circuit
Retry Logic
and System
Monitors
FAR
Failure After
Re-Try
Retry Delay
Retry Counter
N
retry
Fault Bit
FAR_STAT
Programmable
Voltage Reference
0μs
5μs
10μs
20μs
36R
4x
3x
2x
1x
R
R
R
R
+
–
-48V
Overcurrent Event
R
Sense
SMBus
V
EE
FIGURE 27. OVERCURRENT DETECTION/SHORT CIRCUIT PROTECTION WITH PROGRAMMBLE RETRY AND FLAG MONITORS
X80000, X80001
相關PDF資料
PDF描述
X80000 Smart Power Plug Penta-Power Sequence Controller with Hot Swap
X80001 Smart Power Plug Penta-Power Sequence Controller with Hot Swap
X80012Q32I 14 STR PE BLK RoHS Compliant: Yes
X80010Q32I Penta-Power Sequence Controller with Hot swap and System Management
X80013Q32I Connector Wall Plate; Color:Almond; Leaded Process Compatible:Yes; Contact Termination:IDC; No. of Ports:3 RoHS Compliant: Yes
相關代理商/技術參數
參數描述
X80001 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Smart Power Plug Penta-Power Sequence Controller with Hot Swap
X80001Q32I 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Smart Power Plug Penta-Power Sequence Controller with Hot Swap
X80010 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Penta-Power Sequence Controller with Hot swap and System Management
X80-01-01 制造商:MOFLASH SIGNALLING 功能描述:XENON BEACON,AMB,SMALL
X80010Q32I 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Penta-Power Sequence Controller with Hot swap and System Management
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*