參數資料
型號： W949D2CBJX6E
廠商： WINBOND ELECTRONICS CORP
元件分類： DRAM
英文描述： 16M X 32 DDR DRAM, 5 ns, PBGA90
封裝： 8 X 13 MM, 0.80 MM PITCH, HALOGEN FREE AND LEAD FREE, VFBGA-90
文件頁數： 17/60頁
文件大小： 1160K
代理商： W949D2CBJX6E
W949D6CB / W949D2CB
512Mb Mobile LPDDR
Publication Release Date: Jun, 14, 2011
- 24 -
Revision A01-006
Notes:
1.
The table applies when both CKEn-1 and CKEn are HIGH, and after tXSR or tXP has been met if the previous state was
Self Refresh or Power Down.
2.
DESELECT and NOP are functionally interchangeable.
3.
All states and sequences not shown are illegal or reserved.
4.
Current State Definitions:
Idle: The bank has been precharged, and tRP has been met.
Row Active: A row in the bank has been activated, and tRCD has been met. No data bursts/accesses and no register
accesses are in progress.
Read: A READ burst has been initiated, with Auto Precharge disabled, and has not yet terminated or been terminated.
Write: A Write burst has been initiated, with Auto Precharge disabled, and has not yet terminated or been terminated.
5.
Read with AP enabled and Write with AP enabled: The read with Auto Precharge enabled or Write with Auto Precharge
enabled states can be broken into two parts: the access period and the precharge period. For Read with AP, the precharge
period is defined as if the same burst was executed with Auto Precharge disabled and then followed with the earliest
possible PRECHARGE command that still accesses all the data in the burst. For Write with Auto precharge, the precharge
period begins when tWR ends, with tWR measured as if Auto Precharge was disabled. The access period starts with
registration of the command and ends where the precharge period (or tRP) begins. During the precharge period, of the
Read with Auto Precharge enabled or Write with Auto Precharge enabled states, ACTIVE, PRECHARGE, READ, and
WRITE commands to the other bank may be applied; during the access period, only ACTIVE and PRECHARGE
commands to the other banks may be applied. In either case, all other related limitations apply (e.g. contention between
READ data and WRITE data must be avoided).
6.
AUTO REFRESH, SELF REFRESH, and MODE REGISTER SET commands may only be issued when all bank are idle.
7.
A BURST TERMINATE command cannot be issued to another bank; it applies to the bank represented by the current state
only.
8.
READs or WRITEs listed in the Command column include READs and WRITEs with Auto Precharge enabled and READs
and WRITEs with Auto Precharge disabled.
9.
Requires appropriate DM masking.
10.
A WRITE command may be applied after the completion of data output, otherwise a BURST TERMINATE command must
be issued to end the READ prior to asserting a WRITE command.
7. OPERATION
7.1. Deselect
The DESELECT function (
CS = high) prevents new commands from being executed by the LPDDR SDRAM. The
LPDDR SDRAM is effectively deselected. Operations already in progress are not affected.
7.2. No Operation
The NO OPERATION (NOP) command is used to perform a NOP to a LPDDR SDRAM that is selected (
CS =Low).
This prevents unwanted commands from being registered during idle or wait states. Operations already in progress
are not affected.
相關PDF資料
PDF描述
WPD1M16C-80TJI 1M X 16 FAST PAGE DRAM, 80 ns, PDSO42
WPS512K8LC-55TM 512K X 8 STANDARD SRAM, 55 ns, PDSO32
WPS512K8LT-85TI 512K X 8 STANDARD SRAM, 85 ns, PDSO32
W25P012AD-7 32K X 32 STANDARD SRAM, 7 ns, PQFP100
WME128K8-120CC 128K X 8 EEPROM 5V, 120 ns, CDIP32
相關代理商/技術參數
參數描述
W949D2CBJX6ETR 制造商:Winbond Electronics Corp 功能描述:512M MDDR, X32, 166MHZ, 65NM
W949D2CBJX6G 制造商:WINBOND 制造商全稱:Winbond 功能描述:512Mb Mobile LPDDR
W949D2KBJX5E 制造商:Winbond Electronics Corp 功能描述:512M MDDR, X32, 200MHZ 制造商:Winbond Electronics Corp 功能描述:IC MEMORY
W949D2KBJX5I 制造商:Winbond Electronics Corp 功能描述:IC MEMORY
W949D2KBJX6E 制造商:Winbond Electronics Corp 功能描述:512M MDDR, X32, 166MHZ 制造商:Winbond Electronics Corp 功能描述:IC MEMORY
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*