- 您現在的位置：買賣IC網 > PDF目錄359432 > VSC835 (Vitesse Semiconductor Corporation.) 34x34 Crosspoint Switch with Signal Detection PDF資料下載
參數資料
| 型號： | VSC835 |
| 廠商： | Vitesse Semiconductor Corporation. |
| 英文描述： | 34x34 Crosspoint Switch with Signal Detection |
| 中文描述： | 34x34交叉點開關信號檢測 |
| 文件頁數： | 3/18頁 |
| 文件大?。?/td> | 174K |
| 代理商： | VSC835 |
VITESSE
SEMICONDUCTOR CORPORATION
741 Calle Plano, Camarillo, CA 93012 805/388-3700 FAX: 805/987-5896
Page 3
7/24/00
VITESSE
Datasheet
VSC835
2.5 Gbits/sec
34x34 Crosspoint Switch with Signal Detection
G52270-0, Rev. 4.1
Programming Interface
The switch core is programmed through a parallel interface circuit that allows random reads or writes to the
program memory array. The program memory array is buffered to allow multiple programming instructions to
be loaded simultaneously with the CONFIG pin. Parallel programing can be clocked at up to a 50MHz rate and
state read-back can be performed at up to 25MHz.
The program data is composed of two parts: output address and input address. The output address, denoted
by ADDR[5:0], specifies which output channel is to be programmed. The input address, denoted by DATA[5:0],
specifies which input port the switch slice should connect to. The format of the program data is simple binary.
For example: ADDR[5:0] (000100) / DATA[5:0] (000110) would direct output channel Y4 to connect to input
channel A6. The programming state may be verified (read back) by applying the address of the desired output
and asserting RDB. The programming state is unknown at power-on. Additional address space is provided for
access to the monitor registers (see sections below). The microprocessor interface consists of the following sig-
nals. Levels are TTL (see DC Characteristics)
:
Table 1: Programming Interface Signal Table
Loss of Activity (LOA) Monitoring
The LOA function consists of an activity monitor on each input channel, connected directly to the pads.
The state of a monitor (whether or not it has been toggled by an input transition) can be observed by applying
the address
1
of the monitor register corresponding to the signal of interest and asserting RDB. Each monitor
register is four bits in length, covering the state of four inputs. There is one extra two-bit monitor for the 33
rd
and 34
th
inputs. The state of each monitor is transferred to the register on the rising edge of MONCLK, where-
upon the activity monitor is cleared until more activity is detected.
Pin
I/O
Description
D[5:0]
A[5:0]
ALE
CSB
B
I
I
I
Bidirectional data bus to transfer data to/from internal program registers
Address bus to select internal program registers for read-write operations
ALE functionality is not implemented at this time. Tie this pin High.
Chip Select (Active Low): assert this pin whenever the part is being read or programmed.
Write (Active Low): program data will be transferred to the first level internal registers on the rising
edge of this signal (when CSB is also low).
Read (Active Low): program data from the internal program or monitor registers will be read out on the
data bus when this signal goes low (with CSB also low).
Interrupt (Active Low): this signal is asserted when an LOA condition is found
Configure (Active High): assert this signal to transfer queued program information from the first-level
internal registers to the second-level registers, making the programming take effect. This signal may be
tied high to leave the second-level registers transparent so all programming will take effect
immediately. CSB must be active (low) when CONFIG is asserted. CONFIG may be tied to a high-
order bit of the address bus
Monitor states are transferred to monitor registers on the rising edge of this signal. MONCLK is not
expected to exceed 3MHz.
WRB
I
RDB
I
INTB
O
CONFIG
I
MONCLK
I
1. See Memory Map Table
相關PDF資料 |
PDF描述 |
|---|---|
| VSC837 | 3.2Gb/s 68x68 Crosspoint Switch |
| VSC837UG | DIODE ZENER SINGLE 150mW 3Vz 5mA-Izt 0.0667 10uA-Ir 1 SOT-523 3K/REEL |
| VSC838UG | RECTIFIER BRIDGE 25A 200V 300A-ifsm 1.1V-vf 5uA-ir GBPC 100/TRAY |
| VSC838 | 3.2Gb/s 36x37 Crosspoint Switch |
| VSC8476 | XAUI to XFI 10GE & 10GFC Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| VSC837 | 制造商:VITESSE 制造商全稱:Vitesse Semiconductor Corporation 功能描述:3.2Gb/s 68x68 Crosspoint Switch |
| VSC837UG | 制造商:Vitesse Semiconductor Corporation 功能描述: |
| VSC838 | 制造商:VITESSE 制造商全稱:Vitesse Semiconductor Corporation 功能描述:3.2Gb/s 36x37 Crosspoint Switch |
| VSC838UG | 制造商:VITESSE 制造商全稱:Vitesse Semiconductor Corporation 功能描述:3.2Gb/s 36x37 Crosspoint Switch |
| VSC8476 | 制造商:VITESSE 制造商全稱:Vitesse Semiconductor Corporation 功能描述:XAUI to XFI 10GE & 10GFC Transceiver |
發布緊急采購，3分鐘左右您將得到回復。