- 您現在的位置：買賣IC網 > PDF目錄359788 > VSC7216UC-01 (VITESSE SEMICONDUCTOR CORP) Multi-Gigabit Interconnect Chip PDF資料下載
參數資料
| 型號： | VSC7216UC-01 |
| 廠商： | VITESSE SEMICONDUCTOR CORP |
| 元件分類： | 通信及網絡 |
| 英文描述： | Multi-Gigabit Interconnect Chip |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PBGA256 |
| 封裝： | 27 X 27 MM, 1.27 MM PITCH, BGA-256 |
| 文件頁數： | 19/38頁 |
| 文件大?。?/td> | 561K |
| 代理商： | VSC7216UC-01 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
Preliminary Datasheet
VSC7216-01
Multi-Gigabit Interconnect Chip
VITESSE
G52352-0, Rev 3.2
05/05/01
Page 19
VITESSE
SEMICONDUCTOR CORPORATION
741 Calle Plano
Camarillo, CA 93012
Tel: (800) VITESSE
FAX: (805) 987-5896
Email: prodinfo@vitesse.com
Internet: www.vitesse.com
Compatibility with VSC7214 and VSC7211
Care has been taken in the functional definition of the VSC7216-01 to ensure that it is compatible with the
VSC7211 and VSC7214 at the serial link level, and that the transmitter and receiver low-speed interfaces have
compatible modes of operation. It is strongly recommended that the VSC7216-01 not be connected in any way
through the WSO and/or WSI pins to a VSC7211 or VSC7214.
Serial Link Compatibility
The VSC7216-01 uses the same Fibre Channel 8b/10b encoding scheme and the same Word Sync Sequence
used in the VSC7211 and VSC7214. The only difference in serial link operation is that the VSC7211 and
VSC7214 require four consecutive identically-aligned
“
Comma
”
patterns to set the character framing boundary,
while the VSC7216-01 requires a single
“
Comma.
”
This means that from the LOSS_OF_SYNC state, the
VSC7216-01 will make an earlier transition to the RESYNC state (one
“
Comma
”
instead of four) as shown in
Figure 9. Once out of the LOSS_OF_SYNC state, there is no difference in receiver behavior in the absence of
data link errors. When transmitting in 32-bit mode from a VSC7216-01 to a VSC7211 or VSC7214, use
TMODE(2:0)=000 or =1X0 (common transmit interface timing source) to minimize transmitter inter-channel
skew.
Parallel Interface Compatibility
In general, the VSC7216-01 low-speed parallel interfaces can be configured so that there are input and
output signals that are compatible with their VSC7211 and VSC7214 counterparts. On the transmit interface,
the signals Tn(7:0) and C/Dn behave identically on the VSC7216-01 as long as the input timing is referenced to
REFCLK (e.g., TMODE(2:0)=000). On the receive interface, the signals Rn(7:0), ERRn, KCHn and IDLEn
behave identically on the VSC7216-01 as long as the four receive channels present output data centered around
REFCLK (RMODE(1:0)=00) or timed to RCLKA/RCLKNA (RMODE(1:0)=10). When RMODE(1:0)=10, the
VSC7216-01 RCLKn/RCLKNn outputs provide four copies of RCLKA/RCLKNA, which are equivalent to the
VSC7211 and VSC7214 RCLK/RCLKN outputs.
The VSC7216-01 KCHAR input is no longer a synchronous input timed to REFCLK as on the VSC7211
and VSC7214. It is a static input used to define the control character encoding mode when C/Dn=1, as shown in
Table 3. The VSC7216-01 also has a separate WSENn input per channel instead of a common WSYNC input as
on the VSC7211 and VSC7214.
Operational Mode Compatibility
The VSC7211 and VSC7214 specifications define eight operating modes based on the binary combinations
of the RCLKEN, FLOCK and INDEP inputs. Note that these mode inputs control VSC7211 and VSC7214
receiver operation only, and have no effect on transmitter operation. For each of these modes, the equivalent
VSC7216-01 receiver configuration is presented.
VSC7214 MODE 0: RCLKEN=LOW, FLOCK=LOW, INDEP=LOW
Receiver Rn(7:0), ERRn, KCHn and IDLEn outputs are synchronous to REFCLK, IDLE insertion/deletion
is enabled, and the receive channels are word-aligned. The VSC7216-01 should be configured with
RMODE(1:0)=00, FLOCK=0, and WSI connected to its own WSO or to the WSO of another VSC7216-01 if
multiple devices are to be used in parallel. The
WSI
connection allows IDLE insertion/deletion to occur in
parallel across all word-aligned channels.
相關PDF資料 |
PDF描述 |
|---|---|
| VCC6-LAA-622M080 | 3.3 volt LVDS Oscillator, >270MHz |
| VCC6-LAB-622M080 | 3.3 volt LVDS Oscillator, >270MHz |
| VCC6-LAC-622M080 | 3.3 volt LVDS Oscillator, >270MHz |
| VCC6-LAD-622M080 | 3.3 volt LVDS Oscillator, >270MHz |
| VCC6-LAE-622M080 | 3.3 volt LVDS Oscillator, >270MHz |
相關代理商/技術參數 |
參數描述 |
|---|---|
| VSC7216UC-02 | 功能描述:IC TXRX BACKPLANE QUAD 256-BGA RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:25 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:4.5 V ~ 5.5 V 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 供應商設備封裝:16-PDIP 包裝:管件 |
| VSC7216UC-06 | 功能描述:IC TXRX BACKPLANE QUAD 256-BGA RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:25 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:4.5 V ~ 5.5 V 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 供應商設備封裝:16-PDIP 包裝:管件 |
| VSC7216XUC-02 | 功能描述:4/4 Transceiver IEEE 802.3 制造商:microsemi - ent 系列:- 包裝:托盤 零件狀態:過期 類型:收發器 協議:IEEE 802.3 驅動器/接收器數:4/4 雙工:* 接收器滯后:* 數據速率:* 電壓 - 電源:2.375 V ~ 2.625 V 工作溫度:* 安裝類型:表面貼裝 封裝/外殼:256-BGA 供應商器件封裝:* 標準包裝:40 |
| VSC7216XUI-02 | 功能描述:4/4 Transceiver IEEE 802.3 制造商:microsemi - ent 系列:- 包裝:托盤 零件狀態:過期 類型:收發器 協議:IEEE 802.3 驅動器/接收器數:4/4 雙工:- 接收器滯后:- 數據速率:- 電壓 - 電源:2.375 V ~ 2.625 V 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:256-BGA 供應商器件封裝:* 標準包裝:60 |
| VSC7216XUI-06 | 功能描述:4/4 Transceiver IEEE 802.3 制造商:microsemi - ent 系列:- 包裝:托盤 零件狀態:過期 類型:收發器 協議:IEEE 802.3 驅動器/接收器數:4/4 雙工:* 接收器滯后:* 數據速率:* 電壓 - 電源:2.375 V ~ 2.625 V 工作溫度:* 安裝類型:表面貼裝 封裝/外殼:256-BGA 供應商器件封裝:* 標準包裝:60 |
發布緊急采購，3分鐘左右您將得到回復。