- 您現在的位置：買賣IC網 > PDF目錄359400 > VN20N011Y Single Peripheral Driver PDF資料下載
參數資料
| 型號： | VN20N011Y |
| 英文描述： | Single Peripheral Driver |
| 中文描述： | 單外設驅動 |
| 文件頁數： | 4/11頁 |
| 文件大?。?/td> | 193K |
| 代理商： | VN20N011Y |
ELECTRICAL CHARACTERISTICS
(continued)
PROTECTION AND DIAGNOSTICS (continued)
Symbol
V
SCL
(
)
Parameter
Test Conditions
Min.
Typ.
Max.
Unit
Status Clamp Voltage
I
STAT
= 10 mA
I
STAT
= -10 mA
R
LOAD
< 10 m
6
-0.7
V
V
t
SC
Switch-off Time in
Short Circuit Condition
at Start-Up
Over Current
T
c
= 25
o
C
2
5
ms
I
OV
R
LOAD
< 10 m
R
LOAD
< 10 m
-40
≤
T
c
≤
125
o
C
T
c
= 85
o
C
140
A
I
AV
Average Current in
Short Circuit
Open Load Current
Level
Thermal Shut-down
Temperature
Reset Temperature
2.5
A
I
OL
5
700
mA
T
TSD
140
o
C
T
R
125
o
C
(*) The V
is internally clamped at 6V about. It is possible to connect this pin to an higher voltage via an external resistor
calculated to not exceed 10 mA at the input pin.
(
) Status determination > 100
μ
s after the switching edge.
FUNCTIONAL DESCRIPTION
The
device has
indicates
open
temperature conditions. The output signals are
processed by internal logic.
To protect the device against short circuit and
over-current condition, the thermal protection
turns the integrated Power MOS off at a minimum
junction temperature
of 140
temperature returns to about 125
o
C the switch is
automatically turned on again.
In short circuit conditions the protection reacts
with virtually no delay, the sensor being located in
the region of the die where the heat is generated.
a diagnostic output which
circuit
(no
load)
and
over
o
C.
When the
PROTECTING THE DEVICE AGAINST REVER-
SE BATTERY
The simplest way to protect the device against a
continuous reverse battery voltage (-26V) is to
insert a Schottky diode between pin 1 (GND) and
ground, as shown in the typical application circuit
(fig. 3).
The consequences of the voltage drop across
this diode are as follows:
–
If the input is pulled to power GND, a negative
voltage of -V
F
is seen by the device. (V
IL
, V
IH
thresholds and V
STAT
are increased by V
F
with
respect to power GND).
–
The undervoltage shutdown level is increased
by V
F
.
If there is no need for the control unit to handle
external analog signals referred to the power
GND, the best approach is to connect the
reference potential of the control unit to node [1]
(see application circuit in fig. 4), which becomes
the common signal GND for the whole control
board.
In this way no shift of V
IH
, V
IL
and V
STAT
takes
place and no negative voltage appears on the
INPUT pin; this solution allows the use of a
standard diode, with a breakdown voltage able to
handle any ISO normalized negative pulses that
occours in the automotive environment.
VN20N
4/11
相關PDF資料 |
PDF描述 |
|---|---|
| VN20ANSP | Single Peripheral Driver |
| VN20N(011Y) | Hook-Up Wire; Conductor Size AWG:22; No. Strands x Strand Size:7 x 30; Jacket Color:White/Red; Cable/Wire MIL SPEC:MIL-W-76C Type MW; Conductor Material:Copper; Conductor Plating:Tin; Jacket Material:Polyvinylchloride (PVC) RoHS Compliant: Yes |
| VN20N | HIGH SIDE SMART POWER SOLID STATE RELAY |
| VN2106 | N-Channel Enhancement-Mode Vertical DMOS FETs |
| VN2106N3 | N-Channel Enhancement-Mode Vertical DMOS FETs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| VN20N012Y | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single Peripheral Driver |
| VN20NSP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| VN21 | 功能描述:電源開關 IC - 配電 High Side for SSR RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| VN-2-1 | 制造商:Mac8 功能描述: |
| VN21(011Y) | 功能描述:電源開關 IC - 配電 Iso hi side smart pw solid state relay RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
發布緊急采購，3分鐘左右您將得到回復。