- 您現在的位置：買賣IC網 > PDF目錄98278 > TPIC8300IPWRQ1 (TEXAS INSTRUMENTS INC) SPECIALTY ANALOG CIRCUIT, PDSO16 PDF資料下載
參數資料
| 型號： | TPIC8300IPWRQ1 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| 封裝： | PLASTIC, TSSOP-16 |
| 文件頁數： | 7/47頁 |
| 文件大小： | 546K |
| 代理商： | TPIC8300IPWRQ1 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
www.ti.com
SLDS171 – NOVEMBER 2009
Calibration Mode
In calibration mode, microprocessor transmits data to the TPIC83000 in two parts: command frames and data
frames. The data frame immediately follows the command frame. However, unlike Sensor mode, a complete
instruction in Calibration mode needs two command frames and at least two data frames. Calibration mode
consists of four "sub-modes" called Calibration Write, Data Request, Calibration Read, and Mode Select modes.
Furthermore, access to information in the EEPROM and Logic (DSP) registers is dependent upon whether the
device is in Bank or Field addressing mode. Table 9 summarizes the four Calibration Mode command frames.
The following section explains the command and data frames in detail along with the meaning and action of each
bit in these frames.
Table 9. Calibration Mode Profile of Command Frames(1) (2) (3) (4) (5)
POSITION ID
Microprocessor
→IC
PSNID
FLAG
MODE TYPE
DIAG ACKNOWLEDGE
IGNORE
FRAME
DATA NAME
B7 (MSB)
B6
B5
B4
B3
B2
B1
B0 (LSB)
NO.
1
PSNID(1)
PSNID(0)
1
0
DISPSN
ACVOLD
ACVOIN
Data Request
2
PSNID(1)
PSNID(0)
0
NU
RQADCTMP
RQADCDAT
RQTEMP
RQDATA
1
PSNID(1)
PSNID(0)
1
0
DISPSN
NU
Calibration Read
2
PSNID(1)
PSNID(0)
0
Address (5 bit)
1
PSNID(1)
PSNID(0)
1
DISPSN
NU
Calibration Mode Select
2
PSNID(1)
PSNID(0)
0
NU
ACSUNT(6)
ACTMODE(6)
WE
1
PSNID(1)
PSNID(0)
1
0
1
DISPSN
NU
Calibration Write
2
PSNID(1)
PSNID(0)
0
Address (5 bit)
(1)
The request should be ignored when invalid address is received
(2)
Baud rate should be updated after all data is received
(3)
For mode selection request, if WE = 1 and (ACSUNT and ACTMODE) = "old value" , there is no response from IC. Otherwise IC
respond with "old ACSUNT and ACTMODE and WE" data then change mode and/or set WE = 1.
(4)
RQADCTMP: Request 12-bit temperature data
RQADCDAT: Request 14-bit pressure data
RQTEMP: Request 10-bit temperature data
RQDATA: Request 10-bit pressure data
(5)
NU = not used
(6)
All modes should be updated after all data is received.
The command frame profiles are the same in both field and bank addressing modes.
Copyright 2009, Texas Instruments Incorporated
15
Product Folder Link(s): TPIC83000-Q1
相關PDF資料 |
PDF描述 |
|---|---|
| TPIC9201PWPR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| TPIC9201N | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDIP20 |
| TPL0102-100PWR | DIGITAL POTENTIOMETER, PDSO14 |
| TPL0102-100RUCR | DIGITAL POTENTIOMETER, PQCC14 |
| TPL0202-10MRTER | DIGITAL POTENTIOMETER, PQCC16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPIC83R00QRHHRQ1 | 制造商:Texas Instruments 功能描述:- Tape and Reel |
| TPIC84000-Q1 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:LOW-FREQUENCY ANTENNA DRIVER FOR PASSIVE START AND PASSIVE ENTRY |
| TPIC84000TPWPRQ1 | 功能描述:RFID應答器 AC Low-Freq MultiCh Antenna Driver RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| TPIC84125-Q1 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:LOW-FREQUENCY ANTENNA DRIVER FOR PASSIVE START AND PASSIVE ENTRY |
| TPIC84125TPWPRQ1 | 功能描述:RFID應答器 AC Low-Freq Antenna Driver RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。