- 您現在的位置：買賣IC網 > PDF目錄98278 > TPIC8300IPWRQ1 (TEXAS INSTRUMENTS INC) SPECIALTY ANALOG CIRCUIT, PDSO16 PDF資料下載
參數資料
| 型號： | TPIC8300IPWRQ1 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| 封裝： | PLASTIC, TSSOP-16 |
| 文件頁數： | 6/47頁 |
| 文件大?。?/td> | 546K |
| 代理商： | TPIC8300IPWRQ1 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
SLDS171 – NOVEMBER 2009
www.ti.com
Table 7. Bit Descriptions for Sensor Mode Command and Data Frames
CONTROL BIT
VALUE
Position ID matching is enabled and IC respond only when the ID is matched
0
(default)
DISPSN
1
Ignore position ID
0
Sensor mode(Default)
ACTMODE (left in Value)
1
Invalid command
10
Calibration mode
WORD ID (right in Value)
11
Invalid command
0
Band access (default)
ACSUNT
1
Field access
00
Data TX request (Default)
01
Write Request
Command ID
10
Read request
11
Mode selection request
0
EEPROM Write disabled (Default)
WE
1
EEPROM Write Enabled
DIAG FLAG
NORMAL
FAULT/CLEAR
DIAG(1)
0
1
Over-pressure fault condition detected (DIAG1 = 1)
DIAG(0)
0
1
CRC or input voltage error fault detected (DIAG0 = 1)
ACOVLD
0
1
Clear DIAG1 bit (ACOVLD = 1)
ACOVIN
0
1
Clear DIAG0 bit (ACOVIN = 1)(1)
POSITION ID
VALUE
00
ID:0
Default
01
ID:1
PSNID(1:0)
10
ID:2
11
ID:3
(1)
If DIAG0 is high (i.e., DIAG0 = 1) because of CRC error, DIAG0 cannot be cleared by ACOVIN.
Table 8. Overview of Self-Diagnostic and UART Errors
Function
DIAG
Register item
Default
Condition
Clear
DIAG1
Over-pressure
0
Over-pressure condition
ACOVLD = 1 or PUC
DIAG0
CRC Error
0
CRC error exists
WE = 0 or PUC
Self diagnostics
DIAG0
Input fault
(1)
Input voltage error exists
ACOVIN = 1 or PUC
—
PROG_OK
0
Programming voltage = 12.5 V, 15 ms
WE = 0
Frame error
0
Framing error exists
ACVOIN = 1
UART error
Over run error
0
Over run error exists
ACVOIN = 1
Parity error
0
Parity error exists
ACVOIN = 1
(1)
DIAG0 may be set to one depending upon Vcc / SIN / SIP power up condition.
14
Copyright 2009, Texas Instruments Incorporated
Product Folder Link(s): TPIC83000-Q1
相關PDF資料 |
PDF描述 |
|---|---|
| TPIC9201PWPR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| TPIC9201N | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDIP20 |
| TPL0102-100PWR | DIGITAL POTENTIOMETER, PDSO14 |
| TPL0102-100RUCR | DIGITAL POTENTIOMETER, PQCC14 |
| TPL0202-10MRTER | DIGITAL POTENTIOMETER, PQCC16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPIC83R00QRHHRQ1 | 制造商:Texas Instruments 功能描述:- Tape and Reel |
| TPIC84000-Q1 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:LOW-FREQUENCY ANTENNA DRIVER FOR PASSIVE START AND PASSIVE ENTRY |
| TPIC84000TPWPRQ1 | 功能描述:RFID應答器 AC Low-Freq MultiCh Antenna Driver RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| TPIC84125-Q1 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:LOW-FREQUENCY ANTENNA DRIVER FOR PASSIVE START AND PASSIVE ENTRY |
| TPIC84125TPWPRQ1 | 功能描述:RFID應答器 AC Low-Freq Antenna Driver RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。