- 您現在的位置：買賣IC網 > PDF目錄383960 > TMX320C6411AZLZ (Texas Instruments, Inc.) FIXED POINT DIGITAL SIGNAL PROCESSOR PDF資料下載
參數資料
| 型號： | TMX320C6411AZLZ |
| 廠商： | Texas Instruments, Inc. |
| 元件分類： | 數字信號處理 |
| 英文描述： | FIXED POINT DIGITAL SIGNAL PROCESSOR |
| 中文描述： | 定點數字信號處理器 |
| 文件頁數： | 65/119頁 |
| 文件大?。?/td> | 1742K |
| 代理商： | TMX320C6411AZLZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁當前第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁
SPRS196H MARCH 2002 REVISED JULY 2004
65
POST OFFICE BOX 1443
HOUSTON, TEXAS 772511443
IEEE 1149.1 JTAG compatibility statement
The TMS320C6411 DSP requires that both TRST and RESET be asserted upon power up to be properly
initialized. While RESET initializes the DSP core, TRST initializes the DSP’s emulation logic. Both resets are
required for proper operation.
Note: TRST is synchronous and
must
be clocked by TCLK; otherwise, BSCAN may not respond as expected
after TRST is asserted.
While both TRST and RESET need to be asserted upon power up, only RESET needs to be released for the
DSP to boot properly. TRST may be asserted indefinitely for normal operation, keeping the JTAG port interface
and DSP’s emulation logic in the reset state. TRST only needs to be released when it is necessary to use a JTAG
controller to debug the DSP or exercise the DSP’s boundary scan functionality. RESET must be released in
order for boundary-scan JTAG to read the variant field of IDCODE correctly. Other boundary-scan instructions
work correctly independent of current state of RESET.
For maximum reliability, the TMS320C6411 DSP includes an internal pulldown (IPD) on the TRST pin to ensure
that TRST will always be asserted upon power up and the DSP’s internal emulation logic will always be properly
initialized. JTAG controllers from Texas Instruments actively drive TRST high. However, some third-party JTAG
controllers may not drive TRST high but expect the use of a pullup resistor on TRST. When using this type of
JTAG controller, assert TRST to intialize the DSP after powerup and externally drive TRST high before
attempting any emulation or boundary scan operations.
Following the release of RESET, the low-to-high transition of TRST must occur to latch the state of EMU1 and
EMU0. The EMU[1:0] pins configure the device for either Boundary Scan mode or Normal/Emulation mode. For
more detailed information, see the terminal functions section of this data sheet.
Note: The DESIGN_WARNING section of the TMS320C6411 BSDL file contains information and constraints
regarding proper device operation while in Boundary Scan Mode.
EMIF device speed
The rated EMIF speed of this device only applies to the SDRAM interface when in a system that meets the
following requirements:
1 chip-enable (CE) space (maximum of 2 chips) of SDRAM connected to EMIF
up to 1 CE space of buffers connected to EMIF
EMIF trace lengths between 1 and 3 inches
143-MHz SDRAM for 75-MHz operation
Other configurations may be possible, but timing analysis must be done to verify all AC timings are met.
Verification of AC timings is mandatory when using configurations other than those specified above.
TI recommends utilizing the input/output buffer information specification (IBIS) models to analyze all AC timings.
To properly use IBIS models to attain accurate timing analysis for a given system, see the
Using IBIS Models
for Timing Analysis
application report (literature number SPRA839).
To maintain signal integrity, serial termination resistors should be inserted into all EMIF output signal lines (see
the Terminal Functions table for the EMIF output signals).
相關PDF資料 |
PDF描述 |
|---|---|
| TMX320C6411GLZ | FIXED POINT DIGITAL SIGNAL PROCESSOR |
| TMX320C6411ZLZ | FIXED POINT DIGITAL SIGNAL PROCESSOR |
| TMX32C6411AGLZ | FIXED POINT DIGITAL SIGNAL PROCESSOR |
| TMP32C6411AZLZ | FIXED POINT DIGITAL SIGNAL PROCESSOR |
| TMP320C6411AZLZ | FIXED POINT DIGITAL SIGNAL PROCESSOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMX320C6411GLZ | 制造商:Rochester Electronics LLC 功能描述:C6411 1V/300MHZ PROTOTYPES - Bulk 制造商:Texas Instruments 功能描述: |
| TMX320C6411GLZ300 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS |
| TMX320C6411GLZ5E0 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS |
| TMX320C6411GLZA300 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS |
| TMX320C6411GLZA5E0 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS |
發布緊急采購，3分鐘左右您將得到回復。