- 您現在的位置：買賣IC網 > PDF目錄383989 > TDA4885 (NXP SEMICONDUCTORS) 150 MHz video controller with I2C-bus PDF資料下載
參數資料
| 型號： | TDA4885 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 消費家電 |
| 英文描述： | 150 MHz video controller with I2C-bus |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PDIP32 |
| 封裝： | 0.400 INCH, PLASTIC, SOT-232-1, SDIP-32 |
| 文件頁數： | 47/56頁 |
| 文件大小： | 396K |
| 代理商： | TDA4885 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁當前第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
1997 Nov 25
47
Philips Semiconductors
Product specification
150 MHz video controller with I
2
C-bus
TDA4885
13.1
Test application
For high frequency measurements a special test
application and printed-circuit board with only a few
external components is built. Figure 19 shows the test
application circuit and Figs 20 and 21 the layout of the
double sided printed board. Most components are of SMD
type. Short HF loops and minimum crosstalk between the
channels and between signal inputs and outputs are
achieved by properly shaped ground areas.
The HF input signal can be fed to the subclick connectors
V
I1
, V
I2
and V
I3
by a 50
line. The line is then terminated
by a 50
resistor on the board. In channel 3 (pin 10) the
HF input signal can be measured (probe socket).
For operation without input clamping the DC bias can be
provided by VINDC if a short-circuit at J1, J2 and J3 is
made.
OSD input signals (subclick: OSD
1
, OSD
2
, OSD
3
, FBL)
and blanking/clamping inputs (subclick: CLI, HFB) are
terminated with 50
on the board.
The gain modulation input GM (subclick) can be
connected to the three inputs by the jumpers J8 and J4, J5
and J6. With jumper J7 pins 12, 13 and 14 can be
connected to ground (no gain reduction).
There is a separate 4-pin connector for the I
2
C-bus
controller, SDA and SCL have 10 k
pull up resistors to
5 V digital supply.
The beam current limiting pin is fed to the 10-pin main
connector without any special application and should be
connected to the 5 V supply if not used.
DC supply voltage V
P
with a series resistor of 5.6
can be
measured directly at pin 7 via a resistor of 1 k
(V
P
sense).
The supply voltage for the signal channels is fed to VPX
separately and connected to pins 19, 24 and 29 with
decoupling resistors of 5.6
. The supply voltage V
P1
(pin 29) can be measured via 1 k
at pin V
P1
sense.
All supply voltages are filtered near to their pins with
150 pF and 100 nF SMD capacitors and low impedance
0.47
μ
F/63 V electrolytic capacitors.
The signal outputs are loaded with 10 k
and 3 pF to
ground and are connected to a probe socket. With a probe
capacitance of 2 pF the total capacitive load is 5 pF.
The feedback inputs are connected to the voltage outputs
with a 0
resistor (short circuit; RFB1) and via 10 k
(RFB2) connected to the pin VFBDC. The blanking level
can be adjusted with a variation of RFB1, RFB2 and
VFBDC but the resistive output load will be changed.
The blanking level is:
The reference outputs are connected to solder pins.
U
outbl
1
RFB2
+
0.7 V
×
RFB2
RFB1
VFBDC
×
–
=
相關PDF資料 |
PDF描述 |
|---|---|
| TDA4886A | 140 MHz video controller with I2C-bus |
| TDA4886 | 140 MHz video controller with I2C-bus |
| TDA4887 | 160 MHz bus-controlled monitor video preamplifier |
| TDA4887PS | 160 MHz bus-controlled monitor video preamplifier |
| TDA5140 | Transient Voltage Suppressor Diodes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA4885/V2 | 制造商:NXP Semiconductors 功能描述: |
| TDA4886 | 制造商:PHILIPS-SEMI 功能描述: |
| TDA4886A | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:140 MHz video controller with I2C-bus |
| TDA4887 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:160 MHz bus-controlled monitor video preamplifier |
| TDA4887PS | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:160 MHz bus-controlled monitor video preamplifier |
發布緊急采購，3分鐘左右您將得到回復。