參數資料
型號： TDA1315
廠商： NXP Semiconductors N.V.
英文描述： Digital audio input/output circuit DAIO
中文描述： 數字音頻輸入/輸出電路交易代碼
文件頁數： 20/36頁
文件大?。?/td> 411K
代理商： TDA1315
1995 Jul 17
20
Philips Semiconductors
Product specification
Digital audio input/output circuit (DAIO)
TDA1315H
Status
The status register consists of two bytes. A description of
the status register bits is given in Tables 10 and 11. After
a reset all bits in the status register will be one.
The various error conditions of the TDA1315H are
reflected in bits 0 to 6 of the first byte. The error bits are set
(LOW) when the corresponding error conditions occur,
they are reset (HIGH) only after the register has been read
by the microcontroller. Bit 7 reflects the active
transmit/receive state. It is updated after the TDA1315H
configuration, as determined by bit 0 of the first control
register byte, has been changed. This allows verification of
the mode change to, for example, release a mute signal
after a successful change.
Table 10
First byte of status register
BIT
DESCRIPTION
FUNCTION
0
channel status mode
0 = professional
1 = consumer
0 = not locked
1 = locked
0 = error
1 = no error
0 = error
1 = no error
0 = error
1 = no error
0 = error
1 = no error
0 = change
1 = no change
0 = receive
1 = transmit
1
PLL lock condition
2
validity flag
3
parity check
4
biphase violation
5
user data overrun
6
channel status check
7
direction of data
Table 11
Second byte of status register
Note
1.
Bits 6 and 7 in the second byte of the status register
contain the inversion of bits 7 and 6, respectively, of
the channel status, which are used as mode bits.
Reset and standby mode
Figure 11 illustrates the timing for the toggling between
normal and standby mode.
In Figs 11 and 12, when activating PD or RESET, 0 ns can
be taken for t
ON:OSC
when the oscillator is running (e.g.
receive mode).
The TDA1315H uses its internal oscillator for the reset and
standby function. This means that it is not necessary, in
any mode, to apply a clock at the SYSCLKI input for the
TDA1315H to perform the reset or standby function.
For resetting the TDA1315H only a small pulse is
necessary at the RESET input. The device then
automatically starts the oscillator (in the event that it is not
running). The system will then do a synchronous reset
(internally) during approximately 3 internal clock periods.
This t
RESET
starts after the falling edge of RESET or when
the oscillator has started, whichever occurs last. Only
when this resetting has been accomplished will the
external pin programming (e.g. CLKSEL, I
2
SOEN etc.) be
read by the TDA1315H. The TDA1315H is then ready for
use.
BIT
DESCRIPTION
FUNCTION
0
audio mute
0 = enabled
1 = disabled
0 = enabled
1 = disabled
0 = TTL level
1 = high sensitivity
0 = enabled
1 = disabled
0 = SDAUX
1 = IEC or CD
0 = 384f
s
1 = 256f
s
0 = bit 7 set
1 = bit 7 reset
0 = bit 6 set
1 = bit 6 reset
1
IEC output enable
2
select IEC input
3
I
2
S-bus output enable
4
select I
2
S-bus source
5
select clock frequency
6
(1)
channel status (bit 7)
7
(1)
inverse mode bit (bit 6)
相關PDF資料
PDF描述
TDA1315H Digital audio input/output circuit DAIO
TDA1373H General Digital Input GDIN
TDA1386 Noise shaping filter DAC
TDA1386T Noise shaping filter DAC
TDA1515AD Single Audio Amplifier
相關代理商/技術參數
參數描述
TDA1315H 制造商:NXP Semiconductors 功能描述:SPECIALTY CONSUMER CIRCUIT, PQFP44
TDA1315HB-S 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Digital Audio
TDA1319 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
TDA1319T 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Digital Audio Tape Circuit
TDA1348AE 功能描述:48V FAN 127X127X38MM RoHS:是 類別:風扇，熱管理 >> 風扇 - DC 系列:TDA 標準包裝:40 系列:OD8025 風扇類型:管軸式 尺寸/尺寸:方形 - 80mm L x 80mm H x 25mm W 電壓 - 額定:12VDC 功率（瓦特）:- 特點:PWM 控制；速度傳感器（轉速計） RPM:- 雜訊:- 靜態壓力:- 氣流:- 端子:4 引線 軸承類型:密封套筒 工作溫度:- 重量:- 額定電流:- 電壓范圍:- 預期壽命:- 其它名稱:OD802512MSS10A
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*