![](http://datasheet.mmic.net.cn/370000/TCM38C17_datasheet_16738390/TCM38C17_6.png)
TCM38C17IDL
QCombo
FOUR-CHANNEL (QUAD) PCMCOMBO
SLWS040C – JUNE 1996 – REVISED OCTOBER 1999
6
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
electrical characteristics over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted) (continued)
transmit and receive gain and dynamic range, V
DD
= 5 V, T
A
= 25
°
C (see Notes 4, 5, and 6)
PARAMETER
TEST CONDITION
MIN
TYP
±
0.1
MAX
±
0.18
UNIT
Encoder milliwatt response (transmit gain tolerance)
Signal input = 0 dBm0
dBm0
Encoder milliwatt response variation with temperature and
power supplies
TA = –40
°
C to 85
°
C, Supplies =
±
5%
±
0.08
dB
Digital milliwatt response (receive tolerance gain) relative to
zero-transmission-level point
Signal input per CCITT G.711
±
0.1
±
0.18
dBm0
Digital milliwatt response variation with temperature and power
supplies
TA = –40
°
C to 85
°
C,
Supplies =
±
5%
±
0.08
dB
Zero-transmission–level point (
channel
μ
-law
A-law
0.747
Vrms
),
Input buffer configured for unity gain
0.75
Transmit overload signal level, peak-to-peak centered at AREF
3
Vpp
Zero-transmission–level point (0 dBm0), receive
channel
μ
-law
A-law
RL= 600
RL = 600
at maximum gain
(Load is connected between
d PWRO )
PWRO+ and PWRO–)
1.99
Vrms
2
8
Receive overload signal level, fully differential
NOTES: 4. Unless otherwise noted, the analog input is a 0-dBm0, 1020-Hz sine wave, where 0 dBm0 is defined as the zero-reference point of
the channel under test.
5. The input amplifier is set for noninverting unity gain. The digital input is a PCM bit stream generated by passing a 0-dBm0, 1020-Hz
sine wave through an ideal encoder.
6. Receive output is measured single ended in the maximum-gain (unity) configuration. To set the output amplifier for maximum gain,
GSR is connected to PWRO– and the output is taken at PWRO+. All output levels are (sin x)/x corrected.
7.8
Vpp
transmit and receive gain tracking over recommended ranges of supply voltage and operating free-air
temperature, reference level = –10 dBm0
PARAMETER
TEST CONDITION
3 > input level
≥
–40 dBm0
–40 > input level > –50 dBm0
–50
≥
input level
≥
–55 dBm0
3 > input level
≥
–40 dBm0
–40 > input level > –50dBm0
–50
≥
input level
≥
–55 dBm0
MIN
TYP
MAX
±
0.25
±
0.5
±
1.2
±
0.25
±
0.5
±
1.2
UNIT
Transmit gain tracking error, sinusoidal input
dB
Receive gain tracking error, sinusoidal input
dB
noise over recommended ranges of supply voltage and operating free-air temperature
PARAMETER
TEST CONDITION
MIN
TYP
MAX
UNIT
Transmit noise, C-message weighted (
μ
-law), PCMOUT
Transmit noise, psophometrically weighted (A-law), PCMOUT
Receive noise, C-message-weighted quiet code at PWRO+ (
μ
-law)
Receive noise, psophometrically weighted at PWRO+ (A-law)
ANLGIN+ = 0 V
10
12
dBrnC0
ANLGIN+ = 0 V
–80
–75
dBm0p
PCMIN = 11111111
5
12
dBrnC0
PCMIN = 11010101
–85
–79
dBm0p