- 您現在的位置：買賣IC網 > PDF目錄383878 > TAS5110ADADR (Texas Instruments, Inc.) PurePath Digital AMPLIFIER TAS5110A 50-W DIGITAL AMPLIFIER POWER STAGE PDF資料下載
參數資料
| 型號： | TAS5110ADADR |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | PurePath Digital AMPLIFIER TAS5110A 50-W DIGITAL AMPLIFIER POWER STAGE |
| 中文描述： | PurePath Digital數字功放TAS5110A 50 - W數字放大器功率級 |
| 文件頁數： | 8/17頁 |
| 文件大?。?/td> | 165K |
| 代理商： | TAS5110ADADR |
TAS5110A
SLES079A
–
APRIL 2003
–
REVISED MAY 2003
www.ti.com
8
DEVICE OPERATION
Power Sequences
System Power-up/Power-down Sequencing
The recommended power-up/power-down sequence is shown in Figure 3. For proper operation the RESET signal
should be kept low when both DVDD and output power (PVDDA1, PVDDA2, PVDDB1, and PVDDB2) are being
applied. The RESET signal should remain low for at least 1 ms after output power is applied.
1 ms
DVDD(1)
PWDN
PVDDA2
PVDDB2
RESET
≥
1 ms
100
μ
s
100
μ
s
PVDDA1
PVDDB1
(1)For most applications, it is recommended that the PWDN pin be connected directly to the DVDD pin.
Figure 3. Power-Up/Power-Down Sequence
RESET Function
The device is put into a reset condition when the (active low) RESET signal is asserted. While in the reset state, the
input H-bridge control signals consisting of PWM_AP, PWM_AM, PWM_BP, and PWM_BM are ignored, and the
H-bridge MOSFETs are placed in a state where OUTPUTA and OUTPUTB are both low. Asserting the RESET signal
low also causes the short circuit protection latch to be reset. The RESET signal is normally connected to the VALID
signal from the TAS50xx.
Reinitialization Sequence
Proper initial conditions for this device include asserting the RESET signal until the reset operation has completed
(1 ms). Additionally, when using this device with the TAS50xx controller, this function can be accomplished by
asserting the reset pin on the TAS50xx during the reset sequence (see Figure 3).
Audio Application Considerations
Optimal Power Transfer For H-Bridge
The TAS5110A is a power H-bridge that is designed to deliver a maximum of 50 W RMS into a 6-
load. In order
to achieve 50 W into 6
, the system designer must provide an adequate thermal design. See the
Thermal
Methodology for the 32-Pin DAD Package 50 W, 6-
Test
section for a discussion of possible thermal solutions.
Careful attention must be given to the value of the high-voltage power supply level for a given load resistance. See
recommended operating conditions. See the
Maximum Available Power at Common Load Impedances for DAD
Packages
section.
reconstruction output filter
An output reconstruction filter is required between the H-bridge outputs and the loudspeaker load. This second-order
low-pass filter passes the audio information to the loudspeaker, while filtering out the high-frequency out-of-band
information contained in the H-bridge output PWM pulses. The values of the L and C components selected are
dependent on the loudspeaker load impedance.
相關PDF資料 |
PDF描述 |
|---|---|
| TB28F004S3-150 | BYTE-WIDE SMART 3 FlashFile MEMORY FAMILY 4, 8, AND 16 MBIT |
| TB28F008S3-150 | BYTE-WIDE SMART 3 FlashFile MEMORY FAMILY 4, 8, AND 16 MBIT |
| TB28F004S5-100 | BYTE-WIDE SMART 5 FlashFile MEMORY FAMILY 4, 8, AND 16 MBIT |
| TB28F008S5-100 | BYTE-WIDE SMART 5 FlashFile MEMORY FAMILY 4, 8, AND 16 MBIT |
| TB28F016S5-110 | BYTE-WIDE SMART 5 FlashFile MEMORY FAMILY 4, 8, AND 16 MBIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TAS5110ADADRG4 | 功能描述:音頻放大器 50W Dig Amp Power Stage RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TAS5110DAD | 功能描述:音頻放大器 Dig Amp Power Stage RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TAS5110DADG4 | 功能描述:音頻放大器 Dig Amp Power Stage RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TAS5110DADR | 功能描述:音頻放大器 Dig Amp Power Stage RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TAS5110DADRG4 | 功能描述:音頻放大器 Dig Amp Power Stage RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。