- 您現在的位置：買賣IC網 > PDF目錄361343 > T4312816B (TM Technology, Inc.) 8M x 16 SDRAM 2M x 16bit x 4Banks Synchronous DRAM PDF資料下載
參數資料
| 型號： | T4312816B |
| 廠商： | TM Technology, Inc. |
| 英文描述： | 8M x 16 SDRAM 2M x 16bit x 4Banks Synchronous DRAM |
| 中文描述： | 8米× 16 SDRAM的2米x 16Bit的X 4Banks同步DRAM |
| 文件頁數： | 12/70頁 |
| 文件大?。?/td> | 688K |
| 代理商： | T4312816B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
TE
CH
tm
T4312816B
TM Technology Inc. reserves the right
P. 12
to change products or specifications without notice.
Publication Date: FEB. 2007
Revision: A
This field specifies the number of clock cycles from the assertion of the Read command to the first read data.
The minimum whole value of CAS# Latency depends on the frequency of CLK. The minimum whole value
satisfying the following formula must be programmed into this field.
t
CAC
(min)
≤
CAS# Latency X t
CK
A6
A5
A4
0
0
0
0
0
1
0
1
0
0
1
1
1
X
X
Test Mode field (A8~A7)
These two bits are used to enter the test mode and must be programmed to "00" in normal operation.
A8
A7
Test Mode
0
0
normal mode
0
1
Vendor Use Only
1
X
Vendor Use Only
Write Burst Length (A9)
This bit is used to select the burst write length.
A9
Write Burst Length
0
Burst
1
Single Bit
No-Operation command
(RAS# = "H", CAS# = "H", WE# = "H")
The No-Operation command is used to perform a NOP to the SDRAM which is selected (CS# is Low).
This prevents unwanted commands from being registered during idle or wait states.
10 Burst Stop command
(RAS# = "H", CAS# = "H", WE# = "L")
The Burst Stop command is used to terminate either fixed-length or full-page bursts. This command is
only effective in a read/write burst without the auto precharge function. The terminated read burst ends after a
delay equal to the CAS# latency (refer to the following figure). The termination of a write burst is shown in the
following figure.
T0
T 1
T2
T3
CAS# Latency
Reserved
Reserved
2 clocks
3 clocks
Reserved
9
CLK
COMMAND
T4
T5
T6
T7
T8
READ A
NOP
NOP
NOP
NOP
NOP
NOP
NOP
Burst Stop
CAS# latency=2
tCK2, DQ's
CAS# latency=3
tCK3, DQ's
DOUT A0
DOUT A1
DOUT A2
DOUT A3
DOUT A0
DOUT A1
DOUT A2
DOUT A3
The burst ends after a delay equal to the CAS# latency.
Termination of a Burst Read Operation
(Burst Length
4, CAS# Latency = 2, 3)
CLK
COMMAND
T0
T 1
T2
T3
T4
T5
T6
T7
T8
NOP
WRITE A
NOP
NOP
NOP
NOP
NOP
NOP
Burst Stop
CAS# latency= 2, 3
DQ's
DIN A0
DIN A1
DIN A2
don't care
Input data for the Write is masked.
Termination of a Burst Write Operation
(Burst Length = X, CAS# Latency = 1, 2, 3)
相關PDF資料 |
PDF描述 |
|---|---|
| T4312816B-6S | 8M x 16 SDRAM 2M x 16bit x 4Banks Synchronous DRAM |
| T4312816B-6SG | 8M x 16 SDRAM 2M x 16bit x 4Banks Synchronous DRAM |
| T4312816B-7S | 8M x 16 SDRAM 2M x 16bit x 4Banks Synchronous DRAM |
| T4312816B-7SG | 8M x 16 SDRAM 2M x 16bit x 4Banks Synchronous DRAM |
| T431616A | 1M x 16 SDRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T4312816B-6S | 制造商:TMT 制造商全稱:TMT 功能描述:8M x 16 SDRAM 2M x 16bit x 4Banks Synchronous DRAM |
| T4312816B-6SG | 制造商:TMT 制造商全稱:TMT 功能描述:8M x 16 SDRAM 2M x 16bit x 4Banks Synchronous DRAM |
| T4312816B-7S | 制造商:TMT 制造商全稱:TMT 功能描述:8M x 16 SDRAM 2M x 16bit x 4Banks Synchronous DRAM |
| T4312816B-7SG | 制造商:TMT 制造商全稱:TMT 功能描述:8M x 16 SDRAM 2M x 16bit x 4Banks Synchronous DRAM |
| T4314 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TRIANGULAR TYPE |
發布緊急采購，3分鐘左右您將得到回復。