- 您現在的位置：買賣IC網 > PDF目錄225250 > STM1404CRNCQ6F (STMICROELECTRONICS) 1-CHANNEL POWER SUPPLY SUPPORT CKT, QCC16 PDF資料下載
參數資料
| 型號： | STM1404CRNCQ6F |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, QCC16 |
| 封裝： | 3 X 3 MM, ROHS COMPLIANT, QFN-16 |
| 文件頁數： | 5/35頁 |
| 文件大?。?/td> | 366K |
| 代理商： | STM1404CRNCQ6F |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
STM1404
Pin descriptions
2.9
VREF, reference voltage output (1.237, typ)
This is valid only when VCC is between 2.4 V and 3.6 V. When VCC falls below 2.4 V (VSW),
VREF is pulled to ground with an internal 100 kΩ resistor. This is an optional feature
available on the STM1404A. On the STM1404B/C, this pin is VTPU (internally switched VCC
or VBAT). If unused, this pin should float.
2.10
VOUT
This is the supply voltage output. When VCC rises above VSO (battery backup switchover
voltage), VOUT is supplied from VCC. In this condition, VOUT may be connected externally to
VCC through a p-channel MOSFET switch. When VCC falls below the lower value of VSW
(~2.4 V), or VBAT, VOUT is supplied from VBAT. It is recommended that the VOUT pin be
connected externally to a capacitor that will retain a charge for a period of time, in case an
intruder forces VCC or VBAT to ground. The rectifying diode connected from the positive
terminal of the battery to the VBAT pin of the STM1404 will prevent discharge of the
capacitor. Three variations of parts will be offered with the following options:
1.
STM1404A: VOUT remains ON when SAL is active-low; Vccsw pin will continue to
operate in normal mode (see Section 2.3.1: Vccsw, VCC switch output on page 11);
2.
STM1404B: VOUT is taken to High-Z when SAL is active-low; Vccsw pin will be set to
high when this occurs; and
3.
STM1404C: VOUT is driven to ground when SAL is active-low; Vccsw pin will be set to
high when this occurs.
2.11
VTPU
For STM1404B and STM1404C, this pin provides pull-up voltage for the physical tamper
pins (TP1-4). This pin is not to be used as voltage supply source for any other purpose.
Note:
VTPU is the internally switched supply voltage from either the VCC pin or the VBAT pin.
2.12
VCC
This is the supply voltage (2.2 V to 3.6 V).
2.13
VBAT
This is the secondary (backup battery) supply voltage. The pin is connected to the positive
terminal of the battery with a rectifying diode like the BAT54J from STMicroelectronics for
reverse charge protection. Voltage at this pin, after diode rectification, will be approximately
0.2 V less than the battery voltage, and will depend on the type of battery used as well as
the IBAT being drawn. (A capacitor of at least 1.0 F connected between the VBAT pin and
VSS is required.) If no battery is used, connect the VBAT pin to the VCC pin.
2.14
VSS
Ground, VSS, is the reference for the power supply. It must be connected to system ground.
相關PDF資料 |
PDF描述 |
|---|---|
| STM1404CRODQ6F | 1-CHANNEL POWER SUPPLY SUPPORT CKT, QCC16 |
| STM6778YHWB6E | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| STN2907A | PNP Silicon Transistor |
| STP6X14IG | INTERCONNECTION DEVICE |
| STP6X14BL | INTERCONNECTION DEVICE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| STM1404CRNDQ6F | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Security Supervisor with Battery Switchover |
| STM1404CRNHQ6F | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Security Supervisor with Battery Switchover |
| STM1404CRNIQ6F | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Security Supervisor with Battery Switchover |
| STM1404CRNJQ6F | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Security Supervisor with Battery Switchover |
| STM1404CROBQ6F | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Security Supervisor with Battery Switchover |
發布緊急采購，3分鐘左右您將得到回復。