參數資料
型號： STM1404CRNCQ6F
廠商： STMICROELECTRONICS
元件分類： 電源管理
英文描述： 1-CHANNEL POWER SUPPLY SUPPORT CKT, QCC16
封裝： 3 X 3 MM, ROHS COMPLIANT, QFN-16
文件頁數： 3/35頁
文件大?。?/td> 366K
代理商： STM1404CRNCQ6F
STM1404
Pin descriptions
2
Pin descriptions
See Figure 1: Logic diagram and Table 2: Signal names for a brief overview of the signals
connected to this device.
2.1
SAL, security alarm output (open drain)
This signal can be generated when ANY of the following conditions occur:
●
VINT > VHV, where VHV = upper voltage trip limit (4.2 V typ); and where VINT = VCC or
VBAT;
●
VINT < VLV, where VLV = lower voltage trip limit (2.0 V typ); and where VINT = VCC or
VBAT; or
●
When any of the physical tamper inputs, TP1 to TP4, change from their normal states to
the opposite (i.e., intrusion of a physical enclosure).
●
TA > TH, where TH is an upper temperature trip limit specified by the customer (+80°C,
+85°C, and +95°C), factory-programmed (STM1404 only);
●
TA < TL, where TL is a lower temperature trip limit specified by the customer (–25°C or
–35°C), factory-programmed (STM1404 only);
Note:
1
The default state of the SAL output during initial power-up is undetermined.
2
The alarm function will operate either with VCC on or when the part is internally switched
from VCC to VBAT.
2.2
TP1, TP3
Physical tamper detect pin set normally to high (NH). They are connected externally through
a closed switch or a high-impedance resistor to VOUT (in the case of STM1404A) or VTPU (in
the case of STM1404B/C. A tamper condition will be detected when the input pin is pulled
low (see Figure 5 and Figure 6 on page 10). If not used, tie the pin to VOUT (for STM1404A)
or VTPU (for STM1404B/C).
2.3
TP2, TP4
Physical tamper detect pin set normally to low (NL). They are connected externally through
a high-impedance resistor or a closed switch to VSS. A tamper condition will be detected
when the input pin is pulled high (see Figure 7 and Figure 8 on page 10). If not used, tie the
pin to VSS.
2.3.1
Vccsw, VCC switch output
This output is low when VOUT (see Section 2.10: VOUT on page 13) is internally switched to
VCC; in this mode it may be used to turn on an external p-channel MOSFET switch which
can source an external device directly from VCC for currents greater than 80 mA (bypassing
the STM1404).
This pin goes high when VOUT is internally switched to VBAT and may be used as a
“BATTERY ON” indicator.
相關PDF資料
PDF描述
STM1404CRODQ6F 1-CHANNEL POWER SUPPLY SUPPORT CKT, QCC16
STM6778YHWB6E 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6
STN2907A PNP Silicon Transistor
STP6X14IG INTERCONNECTION DEVICE
STP6X14BL INTERCONNECTION DEVICE
相關代理商/技術參數
參數描述
STM1404CRNDQ6F 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Security Supervisor with Battery Switchover
STM1404CRNHQ6F 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Security Supervisor with Battery Switchover
STM1404CRNIQ6F 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Security Supervisor with Battery Switchover
STM1404CRNJQ6F 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Security Supervisor with Battery Switchover
STM1404CROBQ6F 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Security Supervisor with Battery Switchover
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*