- 您現在的位置：買賣IC網 > PDF目錄382560 > STLC2411 (意法半導體) BLUETOOTH BASEBAND PDF資料下載
參數資料
| 型號： | STLC2411 |
| 廠商： | 意法半導體 |
| 英文描述： | BLUETOOTH BASEBAND |
| 中文描述： | 藍牙基帶 |
| 文件頁數： | 14/25頁 |
| 文件大?。?/td> | 216K |
| 代理商： | STLC2411 |
STLC2411
14/25
7.8 V1.2 detailed functionality - Faster Connection
User Perspective - Faster Connection
This feature gives the User about 65% faster connection on average when enabled compared to Bluetooth
spec 1.1 connection procedure.
Technical perspective - Faster Connection
The faster Inquiry functionality is based on a removed/shortened random back off and also a new Inter-
laced Inquiry scan scheme.
The faster Page functionality is based on Interlaced Page Scan.
7.9 V1.2 detailed functionality - Quality of Service
User Perspective - Quality of Service
Small changes to the BT1.1 spec regarding Quality of Service makes a large difference by allowing all
QoS parameters to be communicated over HCI to the link manager that enables efficient BW manage-
ment. Here after a short list of user perspectives:
1) Flush timeout: enables time-bounded traffic such as video streaming to become more robust when the
channel degrades. It sets the maximum delay of an L2CAP frame. It does not enable multiple streams
in one piconet, or heavy data transfer at the same time.
2) Simple latency control: allows the host to set the poll interval. Provides enough support for HID devic-
es mixed with other traffic in the piconet.
7.10 Low power modes
To save power, two low power modes are supported. Depending of the Bluetooth and of the Host's activ-
ity, the STLC2411 autonomously decides to use Sleep Mode or Deep Sleep Mode.
Table 10. Low power modes
Some examples of the low power modes usage:
7.10.1 SNIFF OR PARK
The STLC2411 is in active mode with a Bluetooth connection, once the connection is concluded the SNIFF
or the PARK is programmed. Once one of these two states is entered the STLC2411 goes in Sleep Mode.
After that, the Host may decide to place the STLC2411 in Deep Sleep Mode by putting the UART LINK in
low power mode. The Deep Sleep Mode allows smaller power consumption. When the STLC2411 needs
to send or receive a packet (e.g. at T
SNIFF
or at the beacon instant) it will require the clock and it will go in
active mode for the needed transmission/reception. Immediately afterwards it will go back to the Deep
Low power mode
Sleep Mode
Description
The STLC2411:
- Accepts HCI commands from the Host.
- Supports page- and inquiry scans.
- Supports Bluetooth links that are in Sniff, Hold or Park.
- Can transfer data over Bluetooth links.
- The system clock is still active in part of the design.
The STLC2411:
- Does not accept HCI commands from the Host.
- Keeps track of page- and inquiry scan activities.
Switches between sleep and active mode when it is time to scan.
- Supports Bluetooth links that are in Sniff, Hold or Park.
- Does not transfer data over Bluetooth links.
- The system clock is not active in any part of the design.
Note: Deep Sleep mode is not compatible with a USB transport layer.
Deep Sleep Mode
相關PDF資料 |
PDF描述 |
|---|---|
| STLC2416 | BLUETOOTH BASEBAND WITH INTEGRATED FLASH |
| STLC60243 | DUAL CHANNEL ADSL LINE DRIVER |
| STLC7545 | Enhanced V.34 BIS Analog Front-End(單片模擬前端) |
| STLC7549 | Stereo Audio/MODEM/Telephony Codec(立體聲音頻/調制解調器/電話編解碼器) |
| STLVD210B | DIFFERENTIAL LVDS CLOCK DRIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| STLC2415 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:BLUETOOTH BASEBAND WITH INTEGRATED FLASH |
| STLC2416 | 制造商:STMicroelectronics 功能描述: |
| STLC2450 | 功能描述:射頻無線雜項 Eval Board STLC2450 RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel |
| STLC2500 | 制造商:STMicroelectronics 功能描述:BLUETOOTH CLS II 2.65V TO 2.85V 0.721MBPS 84TFBGA - Trays |
| STLC2500A | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Bluetooth Single Chip |
發布緊急采購，3分鐘左右您將得到回復。